Operating filament

At high operating filament currents, better detectability is obtained, while at low filament currents the life of the filament is extended. Following the instructions provided in the operating manual for the detector will extend filament life. 

The coin-tap test is a widely used teclinique on thin filament winded beams for detection of disbonded and delaminated areas. However, since the sensitivity of this teclinique depends not only on the operator but also on the thickness of the inspected component, the coin-tap testing technique is most sensitive to defects positioned near the surface of the laminate. Therefore, it was decided to constructed a new scaimer for automated ultrasonic inspection of filament winded beams. A complete test rig illustrated in figure 6 was constructed in order to reduce the scanning time. While the beam rotates the probe is moved from one end to the other of the beam. When the scarming is complete it is saved on diskette and can then be evaluated on a PC. The scanner is controlled by the P-scan system, which enables the results to be presented in three dimensions (Top, Side and End view). 

The previous discussion demonstrates that measurement of precise isotope ratios requires a substantial amount of operator experience, particularly with samples that have not been examined previously. A choice of filament metal must be made, the preparation of the sample on the filament surface is important (particularly when activators are used), and the rate of evaporation (and therefore temperature control) may be crucial. Despite these challenges, this method of surface ionization is a useful technique for measuring precise isotope ratios for multiple isotopes. Other chapters in this book discuss practical details and applications. 

Extrusion Processes. Polymer solutions are converted into fibers by extmsion. The dry-extmsion process, also called dry spinning, is primarily used for acetate and triacetate. In this operation, a solution of polymer in a volatile solvent is forced through a number of parallel orifices (spinneret) into a cabinet of warm air the fibers are formed by evaporation of the solvent. In wet extmsion, a polymer solution is forced through a spinneret into a Hquid that coagulates the filaments and removes the solvent. In melt extmsion, molten polymer is forced through a multihole die (pack) into air, which cools the strands into filaments. 

Filament. Eully drawn flat yams and partially oriented (POY) continuous filament yams are available in yam sizes ranging from about 3.3—33.0 tex (30—300 den) with individual filament linear densities of about 0.055 to 0.55 tex per filament (0.5—5 dpf). The fully drawn hard yams are used directly in fabric manufacturing operations, whereas POY yams are primarily used as feedstock for draw texturing. In the draw texturing process, fibers are drawn and bulked by heat-setting twisted yam or by entangling filaments with an air jet. Both textured and hard yams are used in apparel, sleepwear, outerwear, sportswear, draperies and curtains, and automotive upholstery. 

For most hydrardic pressure-driven processes (eg, reverse osmosis), dense membranes in hoUow-fiber configuration can be employed only if the internal diameters of the fibers are kept within the order of magnitude of the fiber-wall thickness. The asymmetric hoUow fiber has to have a high elastic modulus to prevent catastrophic coUapse of the filament. The yield-stress CJy of the fiber material, operating under hydrardic pressure, can be related to the fiber coUapse pressure to yield a more reaUstic estimate of plastic coUapse ... 

Nonwoven bonding processes iatedock webs or layers of fibers, filaments, or yams by mechanical, chemical, or thermal means. The extent of bonding is a significant factor ia determining fabric strength, dexibiUty, porosity, density, loft, and thickness. Bonding is normally a sequential operation performed ia tandem with web formation, but it is also carried out as a separate and distinct operation. 

It is also necessary to reduce the intensity of the radiation admitted into the pyrometer, because pyrometer lamp filaments should not be subjected to temperatures exceeding 1250°C. The reduction is accomplished by a screen or screens in manually operated secondary pyrometers they are usually neutral-density filters. 

---