Nitrates, melting points

To a stirred and refluxing solution of 40 parts of benzene and 35 parts of dimethylformamide (both solvents previously dried azeotropically) are added successively 1.6 parts of sodium hydride and 7.7 parts of Ct-(2,4-dichlorophenyl)imidazole-1-ethanol, (coolingon ice is necessary). After the addition is complete, stirring and refluxing is continued for 30 minutes. Then there are added 7.8 parts of 2,6-dichlorobenzyl chloride and the whole is stirred at reflux for another 3 hours. The reaction mixture is poured onto water and the product 1-[2,4-dichloro-/3 (2,6-dichlorobenzyloxy)phenethyl] imidazole, is extracted with benzene. The extract is washed twice with water, dried, filtered and evaporated in vacuo. The bese residue is dissolved in a mixture of acetone and diisopropyl ether and to this solution is added an excess of concentrated nitric acid solution. The precipitated nitrate salt is filtered off and recrystallized from a mixture of methanol and diisopropyl ether, yielding 1-[2,4-dichloro- (2,6-dichlorobenzyl-oxv)phenethyl] imidazole nitrate melting point 179°C. 

The product, l-[2,4-dichloro-p-(2,4 -dichlorobenzyloxy)phenethyl]imidazole, is extracted with benzene. The extract is washed with water, dried, filtered and evaporated in vacuo. From the residual oily free base, the nitrate salt is prepared in the usual manner in 2-propanol by treatment with concentrated nitric acid, yielding, after recrystallization of the crude solid salt from a mixture of 2-propanol, methanol and diisopropyl ether, l-[2,4-dichloro-p-dichlorobenzyloxy)phenethyl]imidazole nitrate melting point 170.5°C. 

Blasting agents are powerful explosive agents that cannot be detonated by means of a blasting cap when unconfined and are, therefore, very safe to handle. A powerful booster is needed to start detonation. Blasting agents are usually ammonium nitrate (melting point 169.6°C, density 1.725) mixtures sensitized with nonexplosive fuels such as oil or wax. 

Green rhombohedral crystals of iron(II) nitrate hexahy-drate, Fe(N03)2-6H20 (ferrous nitrate), with a melting point 60.5 °C, are obtained from solutions made by dissolving iron in dilute nitric acid. With more concentrated acid, oxidation takes place, and monoclinic pale violet iron(III) nitrate non-ahydrate, Fe(N03 )s -91120 (ferric nitrate), melting point 47 °C, may be crystallized. A colorless hexahydrate can also separate as cubic crystals. Various basic iron(in) nitrates have been described. The eight-coordinate iron(in) anion [Fe(N03)4] has an essentially dodecahedral symmetry with four almost symmetrical bidentate nitrate groups. ... 

Ammonium nitrate (melting point 169.6 °C) exhibits five polymorphs and four enantiotropic changes between —18 and 125 °C, as shown below ... 

Salt baths that are used for certain thermal treatments of aluminium alloys such as homogenisation and solution heat treatment are mixtures of sodium nitrate (melting point, 307 °C) and potassium nitrate (melting point, 334 °C)." The mass loss of aluminium in a nitrate bath is 20 mg-m -h of immersion, which corresponds to a decrease in thickness of less than 0.01 p,m h. This is very acceptable for thermal treatments that do not exceed a few hours. 

Primary aromatic amides are crystaUine sohds with definite melting points. Upon boiling with 10-20 per cent, sodium or potassium hydroxide solution, they are hydrolysed with the evolution of ammonia (vapour turns red htmus paper blue and mercurous nitrate paper black) and the formation of the alkah metal salt of the acid ... 

The melting point of fresh Hitec is 142°C. Hitec heat-transfer salt is very stable but does undergo a slow endothermic breakdown of the nitrite to nitrate. 

Rea.ctlons, When free (R-R, R -tartaric acid (4) is heated above its melting point, amorphous anhydrides are formed which, on boiling with water, regenerate the acid. Further heating causes simultaneous formation of pymvic acid, CH COCOOH pyrotartaric acid, HOOCCH2CH(CH2)COOH and, finally, a black, charred residue. In the presence of a ferrous salt and hydrogen peroxide, dihydroxymaleic acid [526-84-1] (7) is formed. Nitrating the acid yields a dinitro ester which, on hydrolysis, is converted to dihydroxytartaric acid [617 8-1] (8), which upon further oxidation yields tartronic acid [80-69-3] (9). 

Aluminum nitrate is available commercially as aluminum nitrate nonahydrate [7784-27-2], A1(N02)3 9H20. It is a white, crystalline material with a melting point of 73.5°C that is soluble in cold water, alcohols, and acetone. Decomposition to nitric acid [7699-37-2], HNO, and basic aluminum nitrates [13473-90-0], A1(0H) (N03) where x + = 3, begins at 130°C, and dissociation to aluminum oxide and oxides of nitrogen occurs above 500°C. 

Strontium Nitrate. Strontium nitrate, Sr(N02)2, in the anhydrous form is a colorless crystalline powder with a melting point of 570—645°C... 

Imidazole, 4-methyl-annular tautomerism, 5, 363 association, 5, 362 boiling point, 5, 362 bromination, 5, 398 deuteration, 5, 417 diazo coupling, 5, 403 hydrogen bonding, S, 350 hydroxymethylation, 5, 404 iodination, 5, 400 kinetics, 5, 401 mass spectra, 5, 358 melting point, 5, 362 methylation, 5, 364 sulfonation, 5, 397 synthesis, 5, 479-480, 482, 484, 489 Imidazole, 5-methyl-annular tautomerism, 5, 363 Imidazole, l-methyl-4-chloro-ethylation, 5, 386 Imidazole, l-methyl-5-chloro-ethylation, 5, 386 nitration, 5, 395... 

Ammonium nitrate decomposes into nitrous oxide and water. In the solid phase, decomposition begins at about I50°C (302°F) but becomes extensive only above the melting point (I70°C) (338°F). The reaction is first-order, with activation energy about 40 kcal/g mol (72,000 Btii/lb mol). Traces of moisture and Cr lower the decomposition temperature thoroughly dried material has been kept at 300°C (572°F). All oxides of nitrogen, as well as oxygen and nitrogen, have been detected in decompositions of nitrates. 

The mobilities of ions in molten salts, as reflected in their electrical conductivities, are an order of magnitude larger than Arose in Are conesponding solids. A typical value for diffusion coefficient of cations in molten salts is about 5 X lO cm s which is about one hundred times higher Aran in the solid near the melting point. The diffusion coefficients of cation and anion appear to be about the same in Are alkali halides, wiAr the cation being about 30% higher tlrair Are anion in the carbonates and nitrates. 

Amino-l,2,4-triazole has been prepared by evaporating formylguanidine nitrate with sodium carbonate, and from 5(3)-amino-1,2,4-triazole carboxjdic acid-3(S) by heating above its melting point, or by a long digestion with acetic acid. ... 

The nitrate of the base, obtained by acidifying a solution of the free base with nitric acid, had a melting point of 162°C to 164°C and was soluble in water and methanol. 

The experiment may also be repeated using a platinum (indicator) electrode and a tungsten wire reference electrode. If the tungsten electrode has been left idle for more than a few days, the surface must be cleaned by dipping into just molten sodium nitrate (CARE ). The salt should be only just at the melting point or the tungsten will be rapidly attacked it should remain in the melt for a few seconds only and is then thoroughly washed with distilled water. 

---