Nickel intergranular corrosion

This alloy has a nominal composition of 65% nickel, 28% molybdenum and 6% iron. It is generally used in reducing conditions. It is intended to work in very severely corrosive situations after post-weld heat treatment to prevent intergranular corrosion. These alloys have outstanding resistance to all concentrations of hydrochloric acid up to boiling-point temperatures and in boiling sulfuric acid solutions up to 60% concentration. 

The composition of this alloy (54% nickel, 15% molybdenum, 15% chromium, 5% tungsten and 5% iron) is less susceptible to intergranular corrosion at welds. The presence of chromium in this alloy gives it better resistance to oxidizing conditions than the nickel/molybdenum alloy, particularly for durability in wet chlorine and concentrated hypochlorite solutions, and has many applications in chlorination processes. In cases in which hydrochloric and sulfuric acid solutions contain oxidizing agents such as ferric and cupric ions, it is better to use the nickel/molybdenum/ chromium alloy than the nickel/molybdenum alloy. 

A more detailed treatment of sensitisation of austenitic stainless steels, of intergranular corrosion of austenitic stainless steels without sensitisation, and of sensitisation and intergranular corrosion of ferritic stainless steels and high-nickel alloys, is given by Cowan and Tedmon . 

Steverding, B., Intergranular Sulfur Corrosion in Missile Thrust Chamber Nickel Tubes , Corrosion, 18, 433t (1%2)... 

As with most other metal and alloys systems, nickel and certain of its alloys may suffer intergranular corrosion in some circumstances. In practice, intergranular corrosion of nickel alloys is usually confined to the vicinity of welds as a result of the effects produced by the welding operation on the structure of the material in those regions. Alloys that are subjected to other similarly unfavourable thermal treatments may also become susceptible. The compositions of most commercial nickel alloys that are marketed today are. 

Another type of nickel alloy with which problems of intergranular corrosion may be encountered is that based on Ni-Cr-Mo containing about 15% Cr and 15% Mo. In this type of alloy the nature of the grain boundary precipitation responsible for the phenomenon is more complex than in Ni-Cr-Fe alloys, and the precipitates that may form during unfavourable heat treatment are not confined to carbides but include at least one inter-metallic phase in addition. The phenomenon has been extensively studied in recent years . The grain boundary precipitates responsible are molybdenum-rich M C carbide and non-stoichiometric intermetallic ix... 

At temperatures above 300°C, low-carbon nickel (0-02% C) is preferred to avoid the possibility of intergranular attack developing after long exposure if material of higher carbon is employed it should be annealed after fabrication and before exposure to caustic alkalis to prevent stress-assisted intergranular corrosion. 

Henthorne, M., Intergranular Corrosion of Iron and Nickel Base Alloys, Localised Corrosion-Cause of Metal Failure, ASTM STP 516, ASTM, 66 (1972)... 

Table 19.3 Summary of chemical tests used for the determination of susceptibility to intergranular corrosion of iron-nickel Chromium alloys ...

Cowan, R. L. and Tedmon, C. S. (Jr.), Intergranular Corrosion of Iron-Nickel-Chromium Alloys , in Advances in Corrosion Science and Technology, Vol. 3, (eds. M. G. Fontana and R. W. Staehle), Plenum Press (1973)... 

Nickel-based alloys-Determination of resis-ance to intergranular corrosion Corrosion tests in artificial amospheres at very low concentrations of polluting gas(es) Test /. .-sulphur dioxide test for contacts and connectors... 

Austenitic stainless steels are the most significant class of corrosion-resistant alloys for which intergranular corrosion can be a major problem in their satisfactory use. The problem is most often encountered as a result of welding but also may result from stress-relief annealing or incorrect heat treatments. Intergranular corrosion also can occur in ferritic stainless steels and in nickel- and aluminum-base alloys. 

Fig. 7.57 Effect of carbon and nickel content on intergranular corrosion penetration rate of 1 8 wt% Cr-base stainless steels. Alloys sensitized for 100 h at 550 °C. Immersion in boiling 65% nitric acid. Pds., periods (48 h) of exposure. Redrawn from Ref 84...

Nickel-base alloys under certain conditions of composition, thermal history, and environment are susceptible to intergranular corrosion. 

Because of the broad variation in composition and response to thermal treatment of the nickel-base alloys, it is not possible to generalize mechanisms responsible for developing susceptibility to intergranular corrosion. Therefore, the following discussion of the behavior of a Ni-Mo-Cr alloy is used to illustrate the complexity of an interrelationship between alloy composition, heat treatment, corrosion environment and corrosion rate. The alloy has the nominal composition in weight percent of 14.5 to 16.5 Cr, 15 to 17 Mo, 3 to 4.5 W, and 4 to 7 Fe with maximum limits on carbon and silicon. The alloys for which the corrosion data are shown in Fig. 7.59 contained 0.045 to 0.06 wt% carbon and 0.53 to 0.80 wt% silicon and were initially quenched from 1225 15 °C (2235 25 °F), which produced a dispersion of M6C type carbides (M = Mo, W, Si) in austenite (Ref 94). These carbides were not involved in the subsequent corrosion behavior or heat treatments. Heat... 

K. Osozawa, K. Bohnenkamp, and H. Engell, Potentiostatic Study on the Intergranular Corrosion of an Austenitic Chromium-Nickel Stainless Steel, Corros. Sci., Vol 6,1966, p 421-433... 

---