VIII Metals

How then is the positive charge in the (OC)9Co3C-substituted carbonium ions delocalized into the cluster substituent In our first preliminary report on this new class of carbonium ions (45), we suggested that their structure presents an especially favorable opportunity for lateral overlap of a filled er-bonding orbital of a metal-carbon bond and a vacant p orbital on an electron-deficient carbonium ion center /3 to the metal (VIII), that is believed responsible for the high... 

The development of scanning probe microscopies and x-ray reflectivity (see Chapter VIII) has allowed molecular-level characterization of the structure of the electrode surface after electrochemical reactions [145]. In particular, the important role of adsorbates in determining the state of an electrode surface is illustrated by scanning tunneling microscopic (STM) images of gold (III) surfaces in the presence and absence of chloride ions [153]. Electrodeposition of one metal on another can also be measured via x-ray diffraction [154]. 

Nelson et al. [34] determined from void shapes that the ratio 7100/7110 was 1.2, 0.98 and 1.14 for copper at 600°C, aluminum at 550°C, and molybdenum at 2000°C, respectively, and 1.03 for 7100/7111 for aluminum at 450°C. Metal tips in field emission studies (see Section VIII-2C) tend to take on an equilibrium faceting into shapes agreeing fairly well with calculations [133]. 

Fig. VIII-5. Schematic potential energy diagram for electrons in a metal with and without an applied field , work function Ep, depth of the Fermi level. (From Ref. 62.)...

If a surface, typically a metal surface, is irradiated with a probe beam of photons, electrons, or ions (usually positive ions), one generally finds that photons, electrons, and ions are produced in various combinations. A particular method consists of using a particular type of probe beam and detecting a particular type of produced species. The method becomes a spectroscopic one if the intensity or efficiency of the phenomenon is studied as a function of the energy of the produced species at constant probe beam energy, or vice versa. Quite a few combinations are possible, as is evident from the listing in Table VIII-1, and only a few are considered here. 

The composition and chemical state of the surface atoms or molecules are very important, especially in the field of heterogeneous catalysis, where mixed-surface compositions are common. This aspect is discussed in more detail in Chapter XVIII (but again see Refs. 55, 56). Since transition metals are widely used in catalysis, the determination of the valence state of surface atoms is important, such as by ESCA, EXAFS, or XPS (see Chapter VIII and note Refs. 59, 60). 

The classic catalyst consists of Co-Th02-MgO mixtures supported on Kieselguhr (see Ref. 269) group VIII metals, especially Ni, generally are active,... 

Studies to determine the nature of intermediate species have been made on a variety of transition metals, and especially on Pt, with emphasis on the Pt(lll) surface. Techniques such as TPD (temperature-programmed desorption), SIMS, NEXAFS (see Table VIII-1) and RAIRS (reflection absorption infrared spectroscopy) have been used, as well as all kinds of isotopic labeling (see Refs. 286 and 289). On Pt(III) the surface is covered with C2H3, ethylidyne, tightly bound to a three-fold hollow site, see Fig. XVIII-25, and Ref. 290. A current mechanism is that of the figure, in which ethylidyne acts as a kind of surface catalyst, allowing surface H atoms to add to a second, perhaps physically adsorbed layer of ethylene this is, in effect, a kind of Eley-Rideal mechanism. 

We consider next perhaps the bet understood catalyzed reaction the oxidation of CO over group VIII metal catalysts. The reaction is an important environmental one since it involves the conversion of CO to CO2 in automobile catalytic converters. The mechanism is straightforward ... 

In addition to the processes mentioned above, there are also ongoing efforts to synthesize formamide direcdy from carbon dioxide [124-38-9J, hydrogen [1333-74-0] and ammonia [7664-41-7] (29—32). Catalysts that have been proposed are Group VIII transition-metal coordination compounds. Under moderate reaction conditions, ie, 100—180°C, 1—10 MPa (10—100 bar), turnovers of up to 1000 mole formamide per mole catalyst have been achieved. However, since expensive noble metal catalysts are needed, further work is required prior to the technical realization of an industrial process for formamide synthesis based on carbon dioxide. 

The platinum-group metals (PGMs), which consist of six elements in Groups 8— 10 (VIII) of the Periodic Table, are often found collectively in nature. They are mthenium, Ru rhodium, Rh and palladium, Pd, atomic numbers 44 to 46, and osmium. Os indium, Ir and platinum, Pt, atomic numbers 76 to 78. Corresponding members of each triad have similar properties, eg, palladium and platinum are both ductile metals and form active catalysts. Rhodium and iridium are both characterized by resistance to oxidation and chemical attack (see Platinum-GROUP metals, compounds). 

Hydrogenation Catalysts. The key to catalytic hydrogenation is the catalyst, which promotes a reaction which otherwise would occur too slowly to be useful. Catalysts for the hydrogenation of nitro compounds and nitriles are generally based on one or more of the group VIII metals. The metals most commonly used are cobalt, nickel, palladium, platinum, rhodium, and mthenium, but others, including copper (16), iron (17), and tellurium... 

The oxidation reaction between butadiene and oxygen and water in the presence of CO2 or SO2 produces 1,4-butenediol. The catalysts consist of iron acetylacetonate and LiOH (99). The same reaction was also observed at 90°C with Group (VIII) transition metals such as Pd in the presence of I2 or iodides (100). The butenediol can then be hydrogenated to butanediol [110-63-4]. In the presence of copper compounds and at pH 2, hydrogenation leads to furan (101). 

---