Medium-density fibreboard MDF

Eormaldehyde vapour treatment has been applied to improve the dimensional stability of medium-density fibreboard (MDF) (Minato elal, 1992) and albizzia waferboard (Yusuf elal, 1995c). 

Fibres - for medium density fibreboard (MDF), high density fibreboard... 

Early fibreboards were developed by taking fibre from a wet-process fibre line, drying this, mixing it with resin, and pressing it as had been done for particleboard. However, in the last three decades medium density fibreboard (MDF), a UF bonded and dry formed panel, has largely replaced the early fibreboard products. 

The various aminoplastic resins are the most important class of adhesives in the wood-based panels industry, especially for the production of particleboards and medium density fibreboard (MDF), and partly also for oriented strandboard (OSB), plywood, block-boards, and some other types of wood panels. They are also used in the furniture industry as well as in carpenters shops. 

A relatively recent application area for pcD has been in the woodworking industry. Wood composites such as medium density fibreboard (MDF), chipboard, laminated boards with plastic coatings, for use in furniture and on floorings, and also composites, used in wall claddings and in ceilings, all tend to be highly abrasive... 

For a general introduction, see Wood adhesives - basics. Aminoplastic resins are polycondensation products of the reaction of aldehydes with compounds carrying amine or amide groups. Formaldehyde is by far the primary aldehyde used. The name amino-plastic is traditional, but is a misnomer these are thermosetting, irreversibly hardening resins. Two main classes of these resins exist urea-formaldehyde (UF) resins and melamine-formaldehyde (MF) resins. Today, for wood adhesives, pure MF resins are not used anymore because of cost, and only melamine-urea-formaldehyde (MUF) adhesives are used. The main use of these resins is in composite products such as particle board, plywood, medium density fibreboard (MDF), oriented strand board (OSB), glu-lam/flngerjointing and furniture. 

The most common resin for lignocellulosic composites is urea formaldehyde. About 90% of all lignocellulosic composite panel products are bonded with UF [12]. UF is inexpensive, reacts quickly when the composite is hot-pressed, and is easy to use. UF is water-resistant, but not waterproof. As such, its use is limited to interior applications unless special treatments or coatings are applied. UF resins are typically used in the manufacture of products where dimensional uniformity and surface smoothness are of primary concern, for example, particleboard and medium density fibreboard (MDF). Products manufactured with UF resins are designed for interior applications. They can be formulated to cure anywhere from room temperature to 150 °C press times and temperatures can be moderated accordingly. UF resins (often referred to as urea resins) are more economical than PF resins and are the most widely used adhesive for composite wood products. The inherently light colour of UF resins make them quite suitable for the manufacture of decorative products. 

Wood by itself as well as its composite products, such as particleboard, plywood, and medium density fibreboard (MDF) are widely used in indoor products (structural panels. 

The production of high density fibreboard (HDF), medium-density fibreboard (MDF), particleboard (PB) and other wood composite materials uses huge amounts... 

Yousefi, H. (2009) Canola straw as a bio-waste resource for medium density fibreboard (MDF) manufacture. Waste Manage., 29, 2644-2648. 

The results show that the lignocellulosic content and the type of plastic used are the main parameters that control the physical properties of composites. Some of the thermoplastic materials exhibit mechanical properties comparable to those of customary wood fibre products, i.e., medium density fibreboard (MDF) [99, 175] however they show distinctly better behaviour than the MDF and natural wood after exposure to moisture [75, 99, 175]. 

---