Material properties flexural strength

Properties of Dense Silicon Carbide. Properties of the SiC stmctural ceramics are shown in Table 1. These properties are for representative materials. Variations can exist within a given form depending on the manufacturer. Figure 2 shows the flexure strength of the SiC as a function of temperature. Sintered or sinter/HIP SiC is the preferred material for appHcations at temperatures over 1400°C and the Hquid-phase densified materials show best performance at low temperatures. The reaction-bonded form is utilized primarily for its ease of manufacture and not for superior mechanical properties. 

These LCT materials have very high tensile and flexural strength, and excellent mechanical and chemical resistance properties. Some commercial LCT are Vectra (Hoechst-Celanese) and Xydar (Amoco). Du Pont, ICI, GE, and Dow Chemical are also suppHers. Their appHcation in electronic embedding is stiU. in its infancy because of the high temperature processing requirement. Nevertheless, this class of thermoplastic polymers will play an important role in electronic embedding. 

Excellent mechanical properties with very high values for tensile strength, flexural strength and modulus in the flow direction. This applies to unfilled materials and may be further enhanced by incorporation of fibrous fillers. Quoted data for these properties are in the following ranges ... 

The mechanical properties of the laminates are somewhat poorer than observed with phenolic and melamine laminates. Tensile and flexural strength figures are typically about 20% less than for the corresponding P-F and M-F materials and about 60% of values for epoxy laminates. 

To illustrate the correct approach, consider applications in which a material is used in sheet form, as in automotive body panels, and suppose that the service requirements are for stiffness and strength in flexure. First imagine four panels with identical dimensions that were manufactured from the four materials given in Table 3-1. Their flexural stiffnesses and strengths depend directly on the respective material s modulus and strength. All the other factors are shared in common with the other materials, there being no significantly different Poisson ratios. Thus, the relative panel properties are identical with the relative material properties illustrated in Fig. 3-3. Obviously, the metal panels will be stiffer and... 

Amorphous polyarylates are light-amber transparent materials which exhibit mechanical properties comparable to that of unfilled PET in terms of tensile or flexural strength and modulus (Table 2.13) but are notably superior in terms of heat resistance (HDT = 174°C vs. 85°C for PET) and impact strength. 

In addition to spectrosopic studies of the setting chemistry of AB cements, numerous mechanical tests have been used to measure properties of the set materials. This latter group has included determination of compressive and flexural strengths, translucency, electrical conductivity and permittivity. The present chapter describes each of these techniques in outline, and shows how they have been applied. Results obtained using these techniques are described in earlier chapters which deal more thoroughly with each individual type of AB cement. 

Chain scission, causing decrease in molecular weight. Many material properties of polymers are strongly dependent on molecular weight, and are substantially changed by chain scission. Strength - tensile and flexural - decreases, and rate of dissolution in solvent increases. 

A number of mechanical properties have been studied that may affect the clinical success of dental composite restorative materials. Among these are diametral tensile strength (DTS), flexural strength, fracture toughness, elastic modulus, hardness, and fatigue resistance. The mechanical properties should approximate those of tooth structure [183], but correlation of clinical success to any of these properties is limited. 

Chemical, Physical, and Mechanical Tests. Manufactured friction materials are characterized by various chemical, physical, and mechanical tests in addition to friction and wear testing. The chemical tests include thermogravimetric analysis (tga), differential thermal analysis (dta), pyrolysis gas chromatography (pgc), acetone extraction, liquid chromatography (lc), infrared analysis (ir), and x-ray or scanning electron microscope (sem) analysis. Physical and mechanical tests determine properties such as thermal conductivity, specific heat, tensile or flexural strength, and hardness. Much attention has been placed on noise /vibration characterization. The use of modal analysis and damping measurements has increased (see Noise POLLUTION AND ABATEMENT). 

---