Joints outer

Double-lap joint outer adherends, or double-strap joint straps... 

For pipelines in service in chemical plants, it is not usually convenient to place a radiation source inside the pipe and position it to irradiate each welded joint. The radioisotope source container maybe placed on the outer surface of the pipe. The radiation beams then pass through two pipe wall thicknesses to expose films placed diametrically opposite the radiation source, also on the outside of the pipe wall. Other methods, such as magnetic particle inspection of welds in steel pipe, or ultrasonic inspection of welds in pipes of all materials, supplement x-rays in many critical appHcations. The ultrasonic tests can often detect the thin, laminar discontinuities parallel to the pipe surface or the incomplete fusion discontinuities along the weld... 

Gypsum board paper is a special three-ply paper manufactured from repulped newspapers. The face paper or cream face has the ply against the core unsized so that the gypsum crystals can grow into it, as this is the principal form of bonding between the core and facers. The middle ply is sized and the outer ply is more heavily sized and treated to control paint absorption. For the completed gypsum board system to work, the joint treatment and paper must absorb paint at the same rate. 

Corrosion involving nonoxidizing acids can be highly sensitive to flow. Thus regions of high flow and turbulence are often more severely attacked than more quiescent regions. Weirs, lips, and other flow obstructions increase turbulence and thus corrosion. Pipe elbows, tees, and joints are frequently attacked. Outer curves at pipe bends often are more severely wasted than inner bends. 

These are an itnprovised version of a totally enclosed motor to protect its live parts from ingress of water, rain, snow or airborne particles etc. This is achieved by providing them with additional protection such as labyrinths at joints such as bearing end covers, centrifugal discs, end shields and terminal box and giving the outer... 

Rider and Amott were able to produce notable improvements in bond durability in comparison with simple abrasion pre-treatments. In some cases, the pretreatment improved joint durability to the level observed with the phosphoric acid anodizing process. The development of aluminum platelet structure in the outer film region combined with the hydrolytic stability of adhesive bonds made to the epoxy silane appear to be critical in developing the bond durability observed. XPS was particularly useful in determining the composition of fracture surfaces after failure as a function of boiling-water treatment time. A key feature of the treatment is that the adherend surface prepared in the boiling water be treated by the silane solution directly afterwards. Given the adherend is still wet before immersion in silane solution, the potential for atmospheric contamination is avoided. Rider and Amott have previously shown that such exposure is detrimental to bond durability. 

Type S is a floating head type. As the tubes heat up, they expand. As they expand, the floating head moves back and forth, but the pressure seal is not at the sliding joint. The pressure seal is at the fixed shell Joint in the outer head, which contains the pressure. The floating head floats free inside the pressure vessel as the tubes move. Types P and W are floating heads where the movement of the head effects the seal between either the shell-side or tube-side fluid and atmosphere. 

Traditional cold store construction was to build an insulated lining within a masonry shell. The outer skin would be erected in brick and concrete, and rendered as smooth as possible inside with cement plaster, to take the insulation. When the surface was dry, it would have several coats of bitumen applied as a vapour barrier and slabs of insulation material stuck to this with hot bitumen. This was normally carried out in two or more layers so that joints did not pass right through the insulant, but were staggered. The inner skin would be finished with cement plaster, reinforced with wire mesh. The usual insulant was slab cork. 

The electron-pair bond as postulated by Lewis consists of two electrons held jointly by two atoms. By assuming that atoms tend to surround themselves with an outer shell of either shared or unshared electron pairs, usually four in number, but sometimes more or less, Lewis... 

The termination pattern exhibited by A -fibres is entirely different from that of large AjS-fibres. A -fibres travel extensively in Lissauer s tract, overlying the dorsal horn and their terminals form a plexus at the surface of the spinal cord A(5-fibres from high-threshold mechanoreceptors distributed to laminae I, II outer and V. Projections also appear to terminate on the contralateral side, in lamina V. A(5-fibre innervations from deep tissues (muscles and joint) have been shown to terminate exclusively in lamina I, or in laminae IV and V. 

In this method the internal tube is in two pieces and there is less likelihood of making a joint with pinholes in it. The first step is the preparation of the internal tube a length of tubing is drawn off, the end blown out and polished smooth in the flame. The projecting part of the internal tube should be prepared in the same way. The outer tube should be prepared by closing one end to a round end. 

These joints can be made with the internal tube unsupported by inserting the inner tube only after the outer tube is hot enough for it to stick firmly and then proceeding as above. This is rather more difficult and is seldom as satisfactory as wedging the inner tube, although at times one is tempted to avoid this added step. 

Except for components designed in accordance with provisions of (c)(1) above, fluid service requirements for materials stated in this Code shall not restrict their use as cladding or lining in pipe or other components. Fluid service requirements for the outer material (including those for components and joints) shall govern, except that temperature limitations of both inner and... 

---