Iron anionic complexes

Iron hahdes react with haHde salts to afford anionic haHde complexes. Because kon(III) is a hard acid, the complexes that it forms are most stable with F and decrease ki both coordination number and stabiHty with heavier haHdes. No stable F complexes are known. [FeF (H20)] is the predominant kon fluoride species ki aqueous solution. The [FeF ] ion can be prepared ki fused salts. Whereas six-coordinate [FeCy is known, four-coordinate complexes are favored for chloride. Salts of tetrahedral [FeCfy] can be isolated if large cations such as tetraphenfyarsonium or tetra alkylammonium are used. [FeBrJ is known but is thermally unstable and disproportionates to kon(II) and bromine. Complex anions of kon(II) hahdes are less common. [FeCfy] has been obtained from FeCfy by reaction with alkaH metal chlorides ki the melt or with tetraethyl ammonium chloride ki deoxygenated ethanol. 

For alkaline duty, steel can sometimes be used up to approximately pH 11. Zinc, aluminum and similar metals and their alloys have limited use in alkaline conditions because they dissolve, giving complex anions. Iron and steel react in this way above about pH 12. Approximate limits of use for zinc are pH 6-12 and aluminum alloy pH 4-8. Stainless steels, including the lower grades, can be used even in the presence of chloride ions at pH levels of approximately In the absence of halides they can be used up to about pH 13. 

Alkylation of the anion 2 with iodomethane or other haloalkanes provides alkyldicarbonyl(t/5-cyclopentadienyl)iron complexes such as 53,0 (see also Houben-Weyl, Vol. 13/9a, p 209). Migratory insertion of carbon monoxide occurs on treatment with phosphanes or phosphites9 -11 (see also Houben-Weyl, Vol. d3/9a, p257) to provide chiral iron-acyl complexes such as 6. This is the most commonly used preparation of racemic chiral iron-acyl complexes. 

The electronic absorption spectra of the products of one-electron electrochemical reduction of the iron(III) phenyl porphyrin complexes have characteristics of both iron(II) porphyrin and iron(III) porphyrin radical anion species, and an electronic structure involving both re.sonance forms Fe"(Por)Ph] and tFe "(Por—)Ph has been propo.sed. Chemical reduction of Fe(TPP)R to the iron(II) anion Fe(TPP)R) (R = Et or /7-Pr) was achieved using Li BHEt3 or K(BH(i-Bu)3 as the reductant in benzene/THF solution at room temperature in the dark. The resonances of the -propyl group in the F NMR spectrum of Fe(TPP)(rt-Pr) appear in the upfield positions (—0.5 to —6.0 ppm) expected for a diamagnetic porphyrin complex. This contrasts with the paramagnetic, 5 = 2 spin state observed... 

One-electron reduction of the iron(lll) alkyl complexes forms the diamagnetic iron(ll) alkyl anions [Fe(Por)R. The iron(ll) anions do not react with oxygen directly, but are first oxidized by O2 to the corresponding alkyliron(III) complexes, Fe(Por)R, which then insert O2 as described above. 

Iron hydride complexes can be synthesized by many routes. Some typical methods are listed in Scheme 2. Protonation of an anionic iron complex or substitution of hydride for one electron donor ligands, such as halides, affords hydride complexes. NaBH4 and L1A1H4 are generally used as the hydride source for the latter transformation. Oxidative addition of H2 and E-H to a low valent and unsaturated iron complex gives a hydride complex. Furthermore, p-hydride abstraction from an alkyl iron complex affords a hydride complex with olefin coordination. The last two reactions are frequently involved in catalytic cycles. 

Chemically the iron complex 18 is reduced by K/Na alloy in THF to give a green solution of the salt 57. The d7 anion in 57 has been characterized by its ESR spectrum in frozen solution (62). Similarly, on treatment with sodium amalgam, the cobalt complexes 7 and 13 yield dark brownish-red solutions of 58 and 59, respectively. A surprisingly robust PPh4+ salt 60 (mp 158-159°C) could be isolated. Solution and solid state magnetic measurements confirm the presence of two unpaired electrons in these 20-e species as in NiCp2 (60). 

The product is exclusively carbon monoxide, and good turnover numbers are found in preparative-scale electrolysis. Analysis of the reaction orders in CO2 and AH suggests the mechanism depicted in Scheme 4.6. After generation of the iron(O) complex, the first step in the catalytic reaction is the formation of an adduct with one molecule of CO2. Only one form of the resulting complex is shown in the scheme. Other forms may result from the attack of CO2 on the porphyrin, since all the electronic density is not necessarily concentrated on the iron atom [an iron(I) anion radical and an iron(II) di-anion mesomeric forms may mix to some extent with the form shown in the scheme, in which all the electronic density is located on iron]. Addition of a weak Bronsted acid stabilizes the iron(II) carbene-like structure of the adduct, which then produces the carbon monoxide complex after elimination of a water molecule. The formation of carbon monoxide, which is the only electrolysis product, also appears in the cyclic voltammogram. The anodic peak 2a, corresponding to the reoxidation of iron(II) into iron(III) is indeed shifted toward a more negative value, 2a, as it is when CO is added to the solution. 

The reductive dehalogenation of haloalkanes has also been achieved in high yield using polymer supported hydridoiron tetracarbonyl anion (Table 11.15). In reactions where the structure of the alkyl group is such that anionic cleavage is not favoured, carbonylation of the intermediate alkyl(hydrido)iron complex produces an aldehyde (see Chapter 8) [3]. 

Carbonvlation of Benzyl Halides. Several organometallic reactions involving anionic species in an aqueous-organic two-phase reaction system have been effectively promoted by phase transfer catalysts(34). These include reactions of cobalt and iron complexes. A favorite model reaction is the carbonylation of benzyl halides using the cobalt tetracarbonyl anion catalyst. Numerous examples have appeared in the literature(35) on the preparation of phenylacetic acid using aqueous sodium hydroxide as the base and trialkylammonium salts (Equation 1). These reactions occur at low pressures of carbon monoxide and mild reaction temperatures. Early work on the carbonylation of alkyl halides required the use of sodium amalgam to generate the cobalt tetracarbonyl anion from the cobalt dimer(36). 

Figure 1 Transfer chemical potentials for selected iron complexes from water into aqueous methanol (on the molar scale, at 298 K). Ligand abbreviations not appearing in the list at the end of this chapter are acac = acetylacetonate (2,4-pentanedionate) dmpp = l,2-dimethyl-3-hydroxy-4-pyridinonate, the anion from (24) malt = maltolate (2-methyl-3-hydroxy-4-pyranonate, the anion from (233)).

Fio. 10. Possible structures for the arachno anion B4Hg and its iron complex B4HgFe(CO)3. 

When heated with iodide of potassium, rubidium, or cesium and iodine at 300°C in a sealed quartz tube, iron forms tetraiodide complex anion, FeR ... 

---