Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Interfacial fracture toughness

It follows that consists of two stress components a crack tip debond stress, at, and a friction stress component, at is not only a function of the interfacial fracture toughness, G c, but is also dependent on the debond length, t, relative to the total... [Pg.131]

Amorphous PA/PP/PP-MA Melt blending/SEM/XPS/interfacial fracture toughness/effects of PP-MA level ChoandLi 1998... [Pg.569]

Amorphous PA (99-80)/S-IPO (1 % IPO) (1-20) Internal mixer at 210 °C/SEM/interfacial fracture toughness/flexural properties/selective solvent extraction/FTIR Tan et al. 1996... [Pg.580]

Interfacial fracture toughness (Mode I) Capillary length (height)... [Pg.25]

O Dowd, N. P., Shih, G. F. and Stout, M. G. (1992), Test geometry for measuring interfacial fracture toughness. International Journal of Solids and Structures 29, 571-589. [Pg.792]

Wang, J.-S. and Suo, Z. (1990), Experimental determination of interfacial fracture toughness using Brazil-nut sandwiches, Acta Metallurgica et Materialia 38, 1279-1290. [Pg.800]

The Other expression used is that proposed by Rosenfeld et al. in which the interfacial fracture toughness is related to the size of the delaminated area and the load at which delamination of the coating occurs and is given by. [Pg.42]

Table 4. Values of the interfacial fracture toughness for CN coatings (1 p,m thick) deposited on different samples. Table 4. Values of the interfacial fracture toughness for CN coatings (1 p,m thick) deposited on different samples.
Analysis of adhesion and interfacial fracture toughness of coatings... [Pg.320]

Other examples of specimens that may be used to quantify interfacial fracture toughness as a function of mode mix include the blister test, the Brazil... [Pg.331]

Interfacial fracture toughness can be estimated using a number of qualitative methods such as the adhesion tape test, or scratch test. In addition to DCB tests, more quantitative measurements can be made using indentation delamination tests, blister tests, or various interfacial fracture specimens (Section 4). It is important to note that, in the case of organic (viscoelastic) coatings, the tests should be performed at the proper ambient conditions and strain rate. [Pg.344]

Sundararaman, V. and Davidson, B.D., An unsymmetric double cantilever beam test for interfacial fracture toughness determination. Int. J. Solids Struct., 34(7), 799-817 (1997). [Pg.441]

By assuming that the fiber toughness, Rf, is negligible and the interfacial fracture toughness, is equal to the toughness of pristine syntactic foam, R,p Equation (2.14) can be rewritten to the following ... [Pg.52]

Interfacial Fracture Toughness Using Peel Tests... [Pg.2996]

See other pages where Interfacial fracture toughness is mentioned: [Pg.121]    [Pg.208]    [Pg.127]    [Pg.154]    [Pg.267]    [Pg.371]    [Pg.372]    [Pg.357]    [Pg.8]    [Pg.60]    [Pg.371]    [Pg.244]    [Pg.121]    [Pg.208]    [Pg.319]    [Pg.213]    [Pg.232]    [Pg.41]    [Pg.251]    [Pg.981]    [Pg.988]    [Pg.304]    [Pg.313]    [Pg.314]    [Pg.315]    [Pg.344]    [Pg.345]    [Pg.442]    [Pg.122]    [Pg.407]   
See also in sourсe #XX -- [ Pg.13 , Pg.16 ]

See also in sourсe #XX -- [ Pg.313 , Pg.320 ]



SEARCH



Interfacial fracture

Interfacial fracture toughness (Mode

Tough

Tough fracture

© 2024 chempedia.info