Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Transfer injection molding

Figure 25 Schematic diagram of an injection/transfer molding machine [9]. (a) Hydraulic separation unit for upper mold plate, (b) Hydraulic separation unit for middle mold plate, (c) Shuttle system with automatic sprue nipple removal, (d) Brushing unit for cleaning middle mold plate, (e) Hydraulic ejector for automatic ejection. Figure 25 Schematic diagram of an injection/transfer molding machine [9]. (a) Hydraulic separation unit for upper mold plate, (b) Hydraulic separation unit for middle mold plate, (c) Shuttle system with automatic sprue nipple removal, (d) Brushing unit for cleaning middle mold plate, (e) Hydraulic ejector for automatic ejection.
The New ITM Injection-Transfer Molding Technique. Maschinenfabrik J. Dieffenbacher GmbH Co., Germany. [Pg.463]

Wright, R. E., Injection/Transfer Molding of Thermosetting Plastics, Hanser Publishers, New York, 1995, pp. 39-40. [Pg.434]

Molding extrusion Molding extrude Compression molding Injection transfer molding... [Pg.176]

CO/ECO/GECO compounds can be successfully compression, transfer, injection, or injection/transfer molded. Injection molding may be the most commonly used method. When molding with metal inserts, Ty-Ply BN, Chemlok 250, and Chemlok 855 are some of the recommended adhesives for bonding ECO to metal. [Pg.265]

Amino molding compounds can be compression, injection, or transfer molded. Urea molding compound has found wide use and acceptance in the electrical surface wiring device industry. Typical appHcations are circuit breakers, switches, wall plates, and duplex outlets. Urea is also used in closures, stove hardware, buttons, and small housings. Melamine molding compound is used primarily in dinnerware appHcations for both domestic and institutional use. It is also used in electrical wiring devices, ashtrays, buttons, and housings. [Pg.326]

In the manufacture of shaft seals, the molding is the process where the compound and treated metal stamping (phosphated and adhesive applied) are brought together to form the conventional lip type shaft seal. Therefore, it is critical that the compounds used are formulated to suit the molding process. There are three fundamental molding processes in use today compression, injection, and injection/transfer. [Pg.458]

C. F. Johnson, Resin Transfer Molding and Structural Reaction Injection Molding in Engineering Materials Handbook, Vol. 2, ASM, International, USA (1988). [Pg.836]

TS plastic products that are injection, transfer, or compression molded combine thick and thin sections relatively easily since the hardening process is a chemical reaction (Chapter 6). Annular shapes are best made by compression to gain best dimensional control and freedom from distortion. In the compression process, the molding compound is compressed and reduced to the plastic state in the mold. During this process, portions of the material may lie in hard forms in the mold while other portions are flowing rapidly with great force. [Pg.278]

Injection Molding Extrusion Blow Molding Thermoforming Reaction Injection Molding Rotational Molding Compression and Transfer Molding Matched Mold Spray-up... [Pg.438]

Resin transfer molding With vacuum assisted RTM, this process can be called infusion molding. RTM usually uses liquid TS plastics that is transferred or injected into an enclosed mold usually at low pressures of about 60 psi (410 kPa) in which reinforcement... [Pg.517]

Thermosets are processed by compression molding, transfer molding and injection molding or by extrusion, depending on their structure. The pressing temperatures are about 150 to 190°C. Corresponding requirements are placed on the pigments. Dyes are often also used to color thermosets. [Pg.176]

Conversion of cyclic oligomers to composite structures via Resin Transfer Molding (RTM) and Reaction Injection Molding (RIM) techniques has been demonstrated, and will be the subject of subsequent publications. Glass loadings... [Pg.138]

Molding employs a mobile prepolymer that may be thermoset or using a thermoplastic polymer. The polymer can be injection-molded (often for solid objects), blow-molded (for hollow objects such as bottles), rotation-molded, compression-molded, transfer-molded, or thermoformed. Casting is closely related to molding, except that the pressure is typically not used. [Pg.578]

Plastic acrylic denture teeth are made by injection or transfer molding. Acrylic teeth have a higher strength than porcelain teeth and break less readily. However, they resist cold flow, have greater water absorption, and have higher wear rate than porcelain teeth. [Pg.600]

Resin transfer molding (RTM) is a hybrid of two polymer processing techniques we have already described transfer molding and reaction injection molding (RIM). The key difference is that a reinforcement is incorporated during molding to create a composite. [Pg.798]


See other pages where Transfer injection molding is mentioned: [Pg.462]    [Pg.134]    [Pg.136]    [Pg.265]    [Pg.528]    [Pg.277]    [Pg.182]    [Pg.462]    [Pg.134]    [Pg.136]    [Pg.265]    [Pg.528]    [Pg.277]    [Pg.182]    [Pg.377]    [Pg.387]    [Pg.144]    [Pg.85]    [Pg.95]    [Pg.440]    [Pg.490]    [Pg.451]    [Pg.463]    [Pg.278]    [Pg.281]    [Pg.602]    [Pg.615]    [Pg.618]    [Pg.254]    [Pg.204]    [Pg.943]    [Pg.550]    [Pg.308]    [Pg.495]    [Pg.782]    [Pg.95]    [Pg.73]    [Pg.158]   
See also in sourсe #XX -- [ Pg.462 ]




SEARCH



Injection transfer molding process

Injection/transfer molding machine

Transfer mold

Transfer molding

Transfer molding vacuum assisted resin injection

© 2024 chempedia.info