INDEX volatility

Parameter/Test Viscosity, cSta 100°C -40°C Viscosity Index Volatility Loss (%) Pour Point °C... 

Based on the Principal Component Analysis, the LIN index (leaching index) and the VIN index (volatility index) were defined in terms of the first and second PCs, respectively, explaining 92.7% of the total variance [Gramatica and Di Guardo, 2002]. PCs were calculated on a data set of 135 pesticides, described by vapour pressure (Vp), Henry s law constant (H), water solubility (Sw), and octanol/water (Kqw) and organic carbon (Kqc) partition coefficients. The LIN and VIN indices are defined as the following ... 

This term, often called the Fuel Volatility Index (FVI), is expressed by the... 

Tests on vehicles have shown that the volatility index as defined expresses satisfactorily the fuel contribution during hot operation of the engine (Le Breton, 1984). In France, specifications stipulate that its value be limited to 900, 1000 and 1150, respectively, according to the season (summer, spring/fall, winter). The automobile manufacturers, being even more demanding, require in their own specifications that the FVI not be exceeded by 850 in summer. 

Vise, at 100°C, mm2/s Viscosity index (V.l.) Pour point, °C Noack volatility, %... 

Le Breton, M.D. (1984), Hot and cold fuel volatility Indexes of french cars. A cooperative study by the GFC volatility group . SAE paper No. 84-1386, International fuels and lubricants meeting, Baltimore, MD. 

This expression is known as the vapor lock index (VLI) or the front-end volatility index (EEVI). The value of n for U.S. cars is generally reported as 9 when RVP is in kPa (0.13 when pressure is in psi) (23). The maximum level of VLI is set by month and by region according to the ninetieth percentile daily maximum temperature. 

Alkylated aromatics have excellent low temperature fluidity and low pour points. The viscosity indexes are lower than most mineral oils. These materials are less volatile than comparably viscous mineral oils, and more stable to high temperatures, hydrolysis, and nuclear radiation. Oxidation stabihty depends strongly on the stmcture of the alkyl groups (10). However it is difficult to incorporate inhibitors and the lubrication properties of specific stmctures maybe poor. The alkylated aromatics also are compatible with mineral oils and systems designed for mineral oils (see Benzene Toulene Xylenes and ethylbenzene). ... 

Capillary gc/ms, hplc, nmr, ir, and uv are all analytical methods used by the terpene chemist with a good Hbrary of reference spectra, capillary gc/ms is probably the most important method used in dealing with the more volatile terpenes used in the davor and fragrance industry (see Flavors and spices). The physical properties of density, refractive index, boiling point, melting point of derivatives, and specific rotation are used less frequendy but are important in defining product specifications. 

Hplc techniques are used to routinely separate and quantify less volatile compounds. The hplc columns used to affect this separation are selected based on the constituents of interest. They are typically reverse phase or anion exchange in nature. The constituents routinely assayed in this type of analysis are those high in molecular weight or low in volatility. Specific compounds of interest include wood sugars, vanillin, and tannin complexes. The most common types of hplc detectors employed in the analysis of distilled spirits are the refractive index detector and the ultraviolet detector. Additionally, the recent introduction of the photodiode array detector is making a significant impact in the analysis of distilled spirits. 

Aromaticity is the most important property of a carbon black feedstock. It is generally measured by the Bureau of Mines Correlation Index (BMCI) and is an indication of the carbon-to-hydrogen ratio. The sulfur content is limited to reduce corrosion, loss of yield, and sulfur in the product. It may be limited in certain locations for environmental reasons. The boiling range must be low enough so that it will be completely volatilized under furnace time—temperature conditions. Alkane insolubles or asphaltenes must be kept below critical levels in order to maintain product quaUty. Excessive asphaltene content results in a loss of reinforcement and poor treadwear in tire appHcations. 

Industry classification N2 surface area, m /g Particle diameter, nm Fluffy Pellets Fluffy Pellets Nigrometer index Tinting strength Volatile, % pH... 

This technology also allows the control of refractive index profiles by doping. AH vapor-phase techniques use a vapor stream of volatile haUdes such as SiCl, GeCl, BCl, or POCl, and gases such as CI2 or O2. The reactants are oxidized and deposited onto a substrate to produce a soHd glass preform which is then drawn into a fiber. The variations of the technique differ in the way the reactants are oxidized (16). 

The effects of rank on both compressive and impact strength have been studied, and usual minima were found at 20—25% dry, ash-free volatile matter (88—90 wt % carbon). Accordingly, the Hardgrove grindabiUty index exhibits maximum values in this area. 

Specific gravity at 2J C Refractive index Efficiency proportions Cold flex lemp.(°C) Volatility Water extraction (%)" hO OCtane extraction (%r ... 

This section concludes with a reminder that, in addition to the hypohalous acids HOX and metal hypohalites M(OX) , various covalent (molecular) hypohalites are known. Hypochlorites are summarized in Table 17.22. All are volatile liquids or gases at room temperature and are discussed elsewhere (see Index). Organic hypohalites are unstable and rapidly expel HX or RX to form the corresponding aldehyde or ketone ... 

Other important properties include Hash point, volatility, viscosity, specific gravity, cloud point, pour point, and smoke point. Most of these properties are related directly to the boiling range of the kerosene and are not independently variable. The flash point, an index of fire hazard, measures the readiness of a fuel to ignite when exposed to a flame. It is usually mandated by law or government regulation to be 120° or 130° F (48° or 72° C), Volatility, as measured... 

Fluid coking has several characteristics that make it undesirable for most petroleum coke markets. These characteristics are high sulfur content, low volatility, poor crystalline structure, and low grindability index. 

---