Inch , conversion

Location Value of Vara in Inches Conversion Factor, Varas to Meters ... 

In problems such as the mile to inch conversion, it is simpler to combine the two calculations into one. In this case, we write the first step ... 

Several types of internals have been proposed so far. Some studies are presented by Volkct al. (VI2) and Grekelet al. (G15), who studied several arrangements of tubular internals and baffle trays. Volk suggested vertical tubes to increase the contact efficiency. For fluidized beds with diameter of 5-198 inches, conversions for beds of the same equivalent diameter (cf. Section I,C) were found equal. A large heat-exchange surface in the fluid bed is necessary for non-isothermal reactions, so the use of vertical tubes is quite practical. 

CD/ChemSketch is a freeware for drawing chemical structures including organics, organometallics, polymers, and Markush stmctures [31]. It has options for structure cleaning, viewing and naming, inch conversion, stereo descriptors etc. For freeware, no technical support is provided and the functionalities are less compared to the commercial version which has structure search capabilities (Fig. 1.5). 

Unear Umts. The following procedure is used for converting linear units to the proper number of significant places the maximum and minimum limits in inches are calculated. The corresponding two values are converted exacdy into millimeters by multiplying each by the conversion factor 1 in. = 25.4 mm. The results are rounded in accordance with Table 4. 

FMC Corporation, Material Handling Systems Division. To convert ciihic feet per hour to ciihic meters per hour, multiply hy 0.02832 to convert screw diameter in inches to the nearest screw size in centimeters, multiply hy 2.5. See elsewhere for conversion of particle sizes from one measurement system to another. 

The term vacuum is used to e.xpress pressures less than atmospheric pressure (sometimes represented as a negative psi on pressure gauges). Another scale frec]uently used is inches of mercury . The conversion is 14.7 psia = 29.92" Hg. Another scale gaining in popularity is the kilopascal (Kp) scale. 14.7 psia = 100 Kp... 

For conversion, 1 psi h 2.31 ft of water head This represents a column of water at 60°F, 2.31 feet high. The bottom pressure is one pound per square inch (psi) on a gauge. The pressure at the bottom as psi will vary with the density of the fluid. For fluids other than water, the relationship is ... 

Note that psi (pounds per square inch) is pressure on the system and is not expressed as absolute unless the system is under absolute pressure. Feet are expressed as head, not head absolute or gauge (see later example). Note the conversion of psi pressure to feet of head pressure. 

Absolute Pressure Conversion Table Millimeters to Inches Mercury... 

Allyl acetate is a precursor for 1,4-butanediol via a hydrocarbonylation route, which produces 4-acetoxybutanal. The reaction proceeds with a Co(CO)g catalyst in benzene solution at approximately 125°C and 3,000 pounds per square inch. The typical mole H2/CO ratio is 2 1. The reaction is exothermic, and the reactor temperature may reach 180°C during the course of the reaction. Selectivity to 4-acetoxybutanal is approximately 65% at 100% allyl acetate conversion. ... 

Since it is often difficult to visualise the extent of attack in terms of depth from such mass-loss units as mdd, it is common practice to convert these mdd figures into others to indicate depth of penetration, i.e. inches per year (ipy), mils or mm y" . Such calculations suffer from the same defects as the mdd figures in that they take into account neither changes in corrosion rates with time nor non-uniform distribution of corrosion. However, since such conversions are often made it is desirable for the initial reporter of the test results to make the calculations accurately and to report corrosion rates in both mdd and mm y or similar units. 

This conversion factor is exact the inch is defined to be exactly 2.54 cm. The other factors listed in this column are approximate, quoted to four significant figures. Additional digits are available if needed for vary accurate calculations. For example, the pound is defined to be 453.59237 g. 

Specific volume is a conversion of specific gravity into cubic inches per pound. Since the volume of material in a product is the first bit of information established after its shape is formulated, the specific volume is a convenient conversion factor for weight ... 

Combining equations 13.1.16 and 13.1.28 and inserting appropriate conversion factors to let us measure D in inches and L in feet gives... 

Sinfelt et al, J Phys Chem 64 892, 1960). Another investigation is to be made at this temperature and 6.8 atm total pressure with a reactor 1 inch in diameter and 1 ft long. The catalyst used, Pt on alumina, has a bulk density of 187.5 lb/cuft. The volumetric feed rate is to be 12.3 Std cuft/min. What conversion can be expected with feeds composed of (a) 5% n-pentane and 95% hydrogen, (b) 20% n-pentane and 80% hydrogen ... 

The unit conversion of t from inches to feet does not affect the optimum LID), nor do the values of p and S, which are multiplicative constants. The modified objective function, substituting Equation (/) in Equation (j), is therefore... 

You can work all unit conversion problems by this procedure. In some cases, such as the miles to feet problem, only one step is necessary. In other cases, such as the miles to inches problem, more than one step is necessary. However, all steps are of the same type. You will cancel one unit and get a new unit. This process continues until the new unit matches the one that you are seeking. 

---