In polyamides

Fig. 3. Alignment of amide dipoles in polyamide crystals (a) for a two-dimensional array of an odd nylon, nylon-7, (b) for a one-dimensional array of an odd—odd nylon, nylon-5,7 (c) for one-dimensional arrays of polyamides containing even segments an even nylon, nylon-6 an even—even nylon, nylon-6,6 ...

Other noncychc reactions are observed, especially in polyamides of longer carbon chain monomers for example, the linear analogue to the cychc amine reaction is diamine coupling (eq. 10) to form secondary amines that can act as branch points (eq. 11). 

The polyamide copolymer of dodecanoic acid with methylenedi(cyclohexylamine) (MDCHA, PACM) was sold as continuous filament yam fiber under the tradename QIANA. As late as 1981, over 145,000 t was produced using high percentages, typically 80%, of trans, trans MDCHA isomer. The low melting raffinate coproduct left after t,t isomer separation by fractional crystallisation was phosgenated to produce a Hquid aUphatic diisocyanate marketed by Du Pont as Hylene W. Upon terrnination of their QIANA commitment, Du Pont sold the urethane intermediate product rights to Mobay, who now markets the 20% trans, trans—50% cis, trans—30% cis, cis diisocyanate isomer mixture as Desmodur W. In addition to its use in polyamides and as an isocyanate precursor, methylenedi (cyclohexyl amine) is used directiy as an epoxy curative. The Hquid diamine mixture identified historically as PACM-20 is marketed as AMICURE PACM by Anchor Chemical for performance epoxies. 

Use of 1,3 cycloaHphatic diamines in polyamides may be similarly limited by internal amide dehydration of the conformationaHy labile cis isomers to form a tetrahydropyrimidine (38) rather than high molecular weight polyamide. 1,3-Cyclohexanediamine is, however, a component of Spandex polyureas Du Pont uses the hydrogenation product of y -phenylenediamine [108-45-2] (24) captively to produce Lycra (see Fibers, elastomeric). 

About 80-90% of the elemental P produced is reoxidized to (pure) phosphoric acid (p. 521). The rest is used to make phosphorus oxides (p. 503). sulfides (p. 506), phosphorus chlorides and oxochloride (p. 4%). and organic P compounds. A small amount is convened to red phos rftorus (see below) for use in the striking surface of matches for pyrotechnics and as a flame retarding agent (in polyamides). Bulk price for P4 is S2.00/kg. 

American Society for Testing and Materials (ASTM), 242 Amic acid ammonium salt, polyimide cyclization via, 305 Amic acid formation, 301 Amidation reaction scheme, 151 Amide-amide interchange reaction, 158 Amide concentration, in polyamides, 139-141... 

For condensation polymerization, it is necessary to have two functional groups on each monomer and to mix stoichiometric amounts of the reactants. In polyamide production, the starting materials first form nylon salt by proton transfer ... 

Clays have long been used as fillers in polymer systems because of low cost and the improved mechanical properties of the resulting polymer composites. If all other parameters are equal, the efficiency of a filler to improve the physical and mechanical properties of a polymer system is sensitive to its degree of dispersion in the polymer matrix (Krishnamoorti et ah, 1996). In the early 1990s, Toyota researchers (Okada et ah, 1990) discovered that treatment of montmorillonite (MMT) with amino acids allowed dispersion of the individual 1 nm thick silicate layers of the clay scale in polyamide on a molecular. Their hybrid material showed major improvements in physical and mechanical properties even at very low clay content (1.6 vol %). Since then, many researchers have performed investigations in the new field of polymer nano-composites. This has lead to further developments in the range of materials and synthesizing methods available. 

When the -OH of a carboxylic acid is replaced by an -NH2, the compound produced is an amide. Amides are neutral to mildly basic compounds. They can be made from acids, acid chlorides, acid anhydrides, and esters by reaction with ammonia or primary and secondary amines. The amide linkage is found in polyamide resins such as nylon. 

For example, there is a dramatic improvement in modulus, tensile strength, and thermal stability when the aliphatic components in polyamides (nylons) are replaced by aromatic components, resulting in polyaramides such as Kevlar (29). Likewise, poly(ether ether ketone) (PEEK), one of the mechanically strongest condensation... 

These experimental results show conclusively that the deformation factor occurring in the theoretical equation of state offers only a crude approximation to the form of the actual equilibrium stress-strain curve. The reasons behind the observed deviation are not known. It does appear, however, from observations on other rubberlike systems that the type of deviation observed is general. Similar deviations are indicated in TutyP rubber (essentially a cross-linked polyisobutylene) and even in polyamides having network structures and exhibiting rubberlike behavior at high temperatures (see Sec. 4b). 

The combination of a positive charge and reducibility of tetrazolium salts finds use as anticorrosion agents for metals.634,635 The y are components of an oxidant/etchant bath composition for silicon dioxide corrosion-resistant surfaces.636 They are also used as antistatic agents in polyamide... 

Many analytical techniques are in use for the qualitative and quantitative evaluation of monomers and oligomers extracted from PA6 (GC, differential refrac-tometry, IR, PC, SEC, HPLC, RPLC, etc.). FTIR has been used for quantitative analysis of caprolactam oligomer content (extract %) in polyamide-6 [113], The method, which involves a 3h extraction in boiling methanol, is suitable for process control and plant environment. Kolnaar [114] has used FTIR characterisation of fractional extracts with pentane, hexane, and heptane of HDPE for blow moulding applications. Vinyl acetate in packaging film has similarly been determined by quantitative FUR. 

---