Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Hypoid gear

Worm and hypoid gears produce higher oil temperatures because they generate a greater amount of frictional heat. An oil temperature rise of 40°C (104°F) and a maximum oil temperature of 95°C (203°F) is acceptable. With EP oils, it should not exceed 75°C (167°F). [Pg.856]

GL-4 is specified for hypoid gears under severe service ... [Pg.64]

Compared with automotive hypoid gears, gears used in industrial equipment usually operate under moderate loading conditions and place lower demands on the load-carrying capacity of the lubricants. Their typical function is to increase or... [Pg.268]

API GL-4. Lubricants intended for axles with spiral bevel gears operating under moderate to severe conditions of speed and load or axles with hypoid gears operating under moderate speeds and loads. These oils may be used in selected manual transmissions and transaxle applications, where API MT-1 lubricants are unsuitable. [Pg.334]

Hypoid gears Similar in general form to bevel gears, hypoid gears operate on nonintersecting axes (Fig. 5.25). [Pg.513]

Due to the high sliding contact encountered in enclosed worm and hypoid gears, lubricant selection for these should be considered separately from lubrication of other types of enclosed gears. [Pg.868]

Extreme-Pressure (EP) Oils. EP oik are usually high-quaUty petroleum-based oik containing sulfur- and phosphorus-based extreme-pressure additives.These products are especially helpful when high-load conditions exkt and are a must in the lubrication of enclosed hypoid gears. [Pg.869]

Extreme Pressure (EP) additives give the oils high film strength to support extreme loads and pressures met with hypoid gears. (This oil is not recommended for use on machinery with brass washers, bearings, or sleeves unless the EP agent is of a type that does not attack brass.)... [Pg.334]

Wheel gears and hypoid gears generate high pressure on the contact line and greater friction. This will call for heavier oil or one with special additives. [Pg.341]

EP additives are needed for use in hypoid gear trains. Note An EP-additive oil should be checked with the equipment supplier, as some additives are not recommended for use with brass. [Pg.343]

Gear Oiis hypoid gear oil 150 1 9 No optical change except oil residue that could be washed from surface 99 Circular notch impact retained based on 20 hrs impact 150°C of 79 kJ/sq-m Ultrason E 3010 BASF... [Pg.573]

Gear Oils hypoid gear oil 150 1 8 No optical change except oil residue Circular notch Ultrason S 2010 ... [Pg.815]

See other pages where Hypoid gear is mentioned: [Pg.236]    [Pg.239]    [Pg.242]    [Pg.43]    [Pg.842]    [Pg.854]    [Pg.856]    [Pg.868]    [Pg.868]    [Pg.243]    [Pg.243]    [Pg.243]    [Pg.244]    [Pg.946]    [Pg.165]    [Pg.169]    [Pg.169]    [Pg.175]    [Pg.63]    [Pg.327]    [Pg.327]    [Pg.334]    [Pg.335]    [Pg.549]    [Pg.201]    [Pg.296]    [Pg.141]    [Pg.238]    [Pg.266]    [Pg.514]    [Pg.162]    [Pg.2254]    [Pg.1145]   
See also in sourсe #XX -- [ Pg.175 ]



SEARCH



Gear lubricants hypoid gears

Gear, gearing

Gears

Hypoid bevel gears

© 2024 chempedia.info