Hydrophobizing efficiency

The DMA or SMA containing mini-emulsion polymerization can be discussed in terms of its coemulsifier (hydrophobe) efficiency. The value of z (Np°c[CoE]z) for the MMA and St mini-emulsion polymerizations increases in the series (Table 1) ... 

Table 14.2 shows the porosities (pore volume per unit of sample volume) for hydrophilic pores Uphi, hydrophobic pores Upho, and the overall porosity u = Uphi + Upho for Toray paper with two values of PTFE concentrations cptee-Also shown in the table is the parameter hydrophobizing efficiency which represents the ratio of hydrophobic pores (in volume percent) to the PTFE concentration (in volume percent or, as carbon and PTFE have similar density values, in weight percent). This parameter is of importance since high values of the PTFE concentration can lead to an increase in the GDL s ohmic resistance. From the table it can be seen that the PTFE concentration does not significantly influence the volumes of both hydrophilic and hydrophobic pores. At the same time. 

The beneficial effect of water in the arene - arene interaction can be explained by the fact that this solvent is characterised by a low polarisability so that interactions of the aromatic rings with water are less efficient than with most organic solvents. Also the high polarity of water might lead to a polarisation of the aromatic rings, thereby enhancing electrostatic interactions. Finally, hydrophobic interactions may be expected to play a modest role. 

Chapter 5 also demonstrates that a combination of Lewis-acid catalysis and micellar catalysis can lead to accelerations of enzyme-like magnitudes. Most likely, these accelerations are a consequence of an efficient interaction between the Lewis-acid catalyst and the dienophile, both of which have a high affinity for the Stem region of the micelle. Hence, hydrophobic interactions and Lewis-acid catalysis act cooperatively. Unfortunately, the strength of the hydrophobic interaction, as offered by the Cu(DS)2 micellar system, was not sufficient for extension of Lewis-acid catalysis to monodentate dienophiles. 

Venturi scmbbers can be operated at 2.5 kPa (19 mm Hg) to coUect many particles coarser than 1 p.m efficiently. Smaller particles often require a pressure drop of 7.5—10 kPa (56—75 mm Hg). When most of the particulates are smaller than 0.5 p.m and are hydrophobic, venturis have been operated at pressure drops from 25 to 32.5 kPa (187—244 mm Hg). Water injection rate is typicaUy 0.67—1.4 m of Hquid per 1000 m of gas, although rates as high as 2.7 are used. Increasing water rates improves coUection efficiency. Many venturis contain louvers to vary throat cross section and pressure drop with changes in system gas flow. Venturi scmbbers can be made in various shapes with reasonably similar characteristics. Any device that causes contact of Hquid and gas at high velocity and pressure drop across an accelerating orifice wiU act much like a venturi scmbber. A flooded-disk scmbber in which the annular orifice created by the disc is equivalent to a venturi throat has been described (296). An irrigated packed fiber bed with performance similar to a... 

The pify of the leaving group and the hydrophobe chain length can dramatically affect the efficiency of the perhydrolysis reaction. Additionally, the stmcture of the acid portion of the precursor can affect the yield and sensitivity of the reaction to pH. The mono-4-hydroxybenzenesulfonic acid ester of a-decylsuccinic acid (13) undergoes extremely efficient perhydrolysis at much lower pHs than other peracid precursors, eg, decanoyloxybenzene sulfonate (14). This may be because of the neighboring group participation of the adjacent carboxylate as shown in Table 2 (115). 

Electronic effects within the acid portion of the precursor have also been utilized for enhanced reactivity. The 4-hydroxybenzenesulfonate ester of octanoyloxyacetic acid, (15), undergoes efficient perhydrolysis at lower pHs because of the activation of the susceptible carbonyl by the beta-oxygen of the hydrophobic tail (100). 

Hydrophobicity inflkence. Despite of the diphilic character of the NS-rich phase the efficiency of micellar extraction raises with general substrate hydrophobicity increase. The hydrophobicity of ligand is the main factor, which determines the cloud point extraction of complexes. 

The next important phenomena that the result of supramolecular effect are the concentration and proximity effects concerning the components of analytical reaction, even through they are considerably different in hydrophobicity, charge of the species, complexing or collisional type of interaction. The concentration and proximity effects determine the equilibrium of analytical reaction, the efficiencies of intramolecular or intermolecular electronic energy or electron transfer and as a result the sensitivity of analytical reactions. 

These are molecules which contain both hydrophilic and hydrophobic units (usually one or several hydrocarbon chains), such that they love and hate water at the same time. Familiar examples are lipids and alcohols. The effect of amphiphiles on interfaces between water and nonpolar phases can be quite dramatic. For example, tiny additions of good amphiphiles reduce the interfacial tension by several orders of magnitude. Amphiphiles are thus very efficient in promoting the dispersion of organic fluids in water and vice versa. Added in larger amounts, they associate into a variety of structures, filhng the material with internal interfaces which shield the oil molecules—or in the absence of oil the hydrophobic parts of the amphiphiles—from the water [3]. Some of the possible structures are depicted in Fig. 1. A very rich phase... 

This ester was developed to impart greater hydrophilicity in C-terminal peptides that contain large hydrophobic amino acids, since the velocity of deprotection with enzymes often was reduced to nearly useless levels. Efficient cleavage is achieved with the lipase from R. niveus (pH 7, 37°, 16 h, H2O, acetone, 78-91% yield)... 

---