Hydrophile-hydrophobe

Eig. 1. Schematic bioactive polyphosphazenes. (a) General stmcture, where X = hydrophilic /hydrophobic group that hydrolyzes with concurrent polymer breakdown, Y = difunctional group for attaching bioactive agent to polymer, and T = bioactive agent, (b) Actual example where X = —OC H, Y = and... 

A higher hydrophilic/hydrophobic ratio is better for biodegradation. 

Ethoxylation of alkyl amine ethoxylates is an economical route to obtain the variety of properties required by numerous and sometimes smaH-volume industrial uses of cationic surfactants. Commercial amine ethoxylates shown in Tables 27 and 28 are derived from linear alkyl amines, ahphatic /-alkyl amines, and rosin (dehydroabietyl) amines. Despite the variety of chemical stmctures, the amine ethoxylates tend to have similar properties. In general, they are yellow or amber Hquids or yellowish low melting soHds. Specific gravity at room temperature ranges from 0.9 to 1.15, and they are soluble in acidic media. Higher ethoxylation promotes solubiUty in neutral and alkaline media. The lower ethoxylates form insoluble salts with fatty acids and other anionic surfactants. Salts of higher ethoxylates are soluble, however. Oil solubiUty decreases with increasing ethylene oxide content but many ethoxylates with a fairly even hydrophilic—hydrophobic balance show appreciable oil solubiUty and are used as solutes in the oil phase. 

Hydrophilic/hydrophobic properties. In water-based systems, the filler should be compatible with water because filler dispersion occurs in an aqueous medium before a polymer emulsion is added. In general, most fillers are hydropho-... 

The synthesis of block copolymers by macromonotner RAFT polymeriza tion has been discussed in Section 9.5.2 and examples are provide in Table 9.9. RAFT polymerization with thioearbonylthio compounds has been used to make a wide variety of block copolymers and examples arc provided below in Tabic 9.28. The process of block formation is shown in Scheme 9.59. Of considerable interest is the ability to make hydrophilic-hydrophobic block copolymers directly with monomers such as AA, DMA, NIPAM and DMAEMA. Doubly hydrophilic blocks have also been prepared.476 638 The big advantage of RAFT polymerization is its tolerance of unprotected functionality. 

Preparation of polyfethylene oxide) (PEO) and poly(arylene ether) based hydrophilic-hydrophobic block copolymer is of special interest because PEO has been proven to be particularly reliable and versatile for the surface modification of biomaterials. The first poly(ediylene oxide)-/ /oc/c-polysulfonc (PEO-fc-PSF) copolymers were reported by Aksenov et al.217 They employed diisocyanate chemistry to link hydroxy-terminated sulfone oligomers and polyfethylene... 

In highly diluted solutions the surfactants are monodispersed and are enriched by hydrophil-hydrophobe-oriented adsorption at the surface. If a certain concentration which is characteristic for each surfactant is exceeded, the surfactant molecules congregate to micelles. The inside of a micelle consists of hydrophobic groups whereas its surface consists of hydrophilic groups. Micelles are dynamic entities that are in equilibrium with their surrounded concentration. If the solution is diluted and remains under the characteristic concentration, micelles dissociate to single molecules. The concentration at which micelle formation starts is called critical micelle concentration (cmc). Its value is characteristic for each surfactant and depends on several parameters [189-191] ... 

The hydrophilic/hydrophobic SIN composition of PDMS with poly(HEMA) and poly(AAC) were proposed as a potential apphcation for high-permeability soft contact lenses. Other sUicone-containing IPNs for contact lenses include polymerization of MMA in the presence of polymerized methacryloxypropyl trimethoxysilane, the cross-linking of a polymeric hydrogel of a copolymer of NVP during the final compression or injection-moulding process. 

The physico-chemical properties of gels, such as hydrophilicity-hydrophobicity balance and ionic nature, can be changed by the selection of suitable prepolymers. 

Drug Release from PHEMA-l-PIB Networks. Amphiphilic networks due to their distinct microphase separated hydrophobic-hydrophilic domain structure posses potential for biomedical applications. Similar microphase separated materials such as poly(HEMA- -styrene-6-HEMA), poly(HEMA-6-dimethylsiloxane- -HEMA), and poly(HEMA-6-butadiene- -HEMA) triblock copolymers have demonstrated better antithromogenic properties to any of the respective homopolymers (5-S). Amphiphilic networks are speculated to demonstrate better biocompatibility than either PIB or PHEMA because of their hydrophilic-hydrophobic microdomain structure. These unique structures may also be useful as swellable drug delivery matrices for both hydrophilic and lipophilic drugs due to their amphiphilic nature. Preliminary experiments with theophylline as a model for a water soluble drug were conducted to determine the release characteristics of the system. Experiments with lipophilic drugs are the subject of ongoing research. 

A novel approach for ion sensing is based on the use of potential-sensitive or polarity-sensitive dyes (PSDs) and was presented first106 in 1987. PSDs are charge dyes and typically located at the interface between a lipophilic sensor phase and a hydrophilic sample phase. The transport of an ion into the lipophilic sensor layer causes the PSD to be displaced from the hydrophilic/hydrophobic interface into the interior of the respective phase (or vice versa), thereby undergoing a significant change in its fluorescence properties107 110. 

---