Hydrogen catalysts, nickel

HYDROGENATION, CATALYSTS Nickel on alumina. Nickel-Graphite. Palladium-Poly(ethylenimine). Palladium catalysts. Raney nickel. Rhodium catalysts. 

The activity of the usual metallic hydrogenation catalysts (nickel, cobalt, palladium, and platinum) for the hydrogenation of ethylenic substances is impaired by carbon monoxide. Carbon monoxide also has been shown to inhibit the catalytic activity of a copper hydrogenation catalyst (Pease and Stewart, 6). 

The classical hydrogenation catalysts nickel, platinum, and palladium have proved useful in such reactions also in special cases ruthenium56 and iron57... 

The uncatalyzed addition of hydrogen to an alkene although exothermic is very slow The rate of hydrogenation increases dramatically however m the presence of cer tain finely divided metal catalysts Platinum is the hydrogenation catalyst most often used although palladium nickel and rhodium are also effective Metal catalyzed addi tion of hydrogen is normally rapid at room temperature and the alkane is produced m high yield usually as the only product... 

The French chemist Paul Sabatier received the 1912 Nobel Prize in chemistry for his discovery that finely di vided nickel is an effective hydrogenation catalyst... 

Disposal of spent hydrogenation catalyst requires a special chemical waste landfill because of its nickel content and the fact that oil-soaked catalysts tend to be pyrophoric. Compared to disposal costs, reprocessing to recover the nickel may become economically viable. 

Goal Upgrading via Fischer-Tropsch. The synthesis of methane by the catalytic reduction of carbon monoxide and hydrogen over nickel and cobalt catalysts at atmospheric pressure was reported in 1902 (11). 

Nickel Arsenate. Nickel arsenate [7784-48-7] Ni2(As0 2 8H20, is a yellowish green powder, density 4.98 g/cm. It is highly iasoluble ia water but is soluble ia acids, and decomposes on heating to form As20 and nickel oxide. Nickel arsenate is formed by the reaction of a water solution of arsenic anhydride and nickel carbonate. Nickel arsenate is a selective hydrogenation catalyst for iaedible fats and oils (59). 

Hydrogenation Catalysts. The key to catalytic hydrogenation is the catalyst, which promotes a reaction which otherwise would occur too slowly to be useful. Catalysts for the hydrogenation of nitro compounds and nitriles are generally based on one or more of the group VIII metals. The metals most commonly used are cobalt, nickel, palladium, platinum, rhodium, and mthenium, but others, including copper (16), iron (17), and tellurium... 

In past years, metals in dilute sulfuric acid were used to produce the nascent hydrogen reductant (42). Today, the reducing agent is hydrogen in the presence of a catalyst. Nickel, preferably Raney nickel (34), chromium or molybdenum promoted nickel (43), or supported precious metals such as platinum or palladium (35,44) on activated carbon, or the oxides of these metals (36,45), are used as catalysts. Other catalysts have been suggested such as molybdenum and platinum sulfide (46,47), or a platinum—nithenium mixture (48). 

Salts of neodecanoic acid have been used in the preparation of supported catalysts, such as silver neodecanoate for the preparation of ethylene oxide catalysts (119), and the nickel soap in the preparation of a hydrogenation catalyst (120). Metal neodecanoates, such as magnesium, lead, calcium, and zinc, are used to improve the adherence of plasticized poly(vinyl butyral) sheet to safety glass in car windshields (121). Platinum complexes using neodecanoic acid have been studied for antitumor activity (122). Neodecanoic acid and its esters are used in cosmetics as emoUients, emulsifiers, and solubilizers (77,123,124). Zinc or copper salts of neoacids are used as preservatives for wood (125). 

Hydrogenation. Hydrogenation is one of the oldest and most widely used appHcations for supported catalysts, and much has been written in this field (55—57). Metals useflil in hydrogenation include cobalt, copper, nickel, palladium, platinum, rhenium, rhodium, mthenium, and silver, and there are numerous catalysts available for various specific appHcations. Most hydrogenation catalysts rely on extremely fine dispersions of the active metal on activated carbon, alumina, siHca-alumina, 2eoHtes, kieselguhr, or inert salts, such as barium sulfate. 

Electroless reactions must be autocatalytic. Some metals are autocatalytic, such as iron, in electroless nickel. The initial deposition site on other surfaces serves as a catalyst, usually palladium on noncatalytic metals or a palladium—tin mixture on dielectrics, which is a good hydrogenation catalyst (20,21). The catalyst is quickly covered by a monolayer of electroless metal film which as a fresh, continuously renewed clean metal surface continues to function as a dehydrogenation catalyst. Silver is a borderline material, being so weakly catalytic that only very thin films form unless the surface is repeatedly cataly2ed newly developed baths are truly autocatalytic (22). In contrast, electroless copper is relatively easy to maintain in an active state commercial film thicknesses vary from <0.25 to 35 p.m or more. 

An a priori choice of an optimum acetylene hydrogenation catalyst is not always easy. For instance, hydrogenation of octadeca-3,6-diynol over P-2 nickel gave the corresponding (Z,Z) dienol satisfactorily (37), but when the... 

Recently, other authors when studying the activation of hydrogen by nickel and nickel-copper catalysts in the hydrogen-deuterium exchange reaction concentrated for example only on the role of nickel in these alloys (56) or on a correlation between the true nickel concentration in the surface layer of an alloy, as stated by the Auger electron spectroscopy, and the catalytic activity (57). 

---