Poly hydrocarbon polymers

Satoh K., Sugiyama H., Kamigaito M., Biomass-derived heat-resistant aticycUc hydrocarbon polymers poly(terpenes) and their hydrogenated derivatives. Green Chem., 8(10), 2006, 878-882. 

As a class the aliphatic polyalkenamers have low values due to a combination of low chain stiffness and low interchain attraction. The presence of double bonds has the effect of increasing the flexibility of adjacent single bonds (see Chapter 4) and overall this leads to a reduction in. Thus in the sequence from polydecenamer down to polypentenamer an increase in the double bond concentration leads to a lowering of Tg. On the other hand the Tg of polybutenamer, i.e. poly butadiene, is somewhat higher than that of polypentenamer, presumably because the proportion of stiff links, i.e. double bonds, becomes sufficiently high to override the flexibilising effect on adjacent chains. Consequently the polypentenamers have the lowest Tg values known for hydrocarbon polymers (cis- -114°C, trans- -97°C). 

Hydrogen, which is a major product in the radiolysis of most hydrocarbon polymers, is only a minor product in the radiolysis of poly(olefin sulfone)s, although it is of the largest yield between the minor products. Hydrogen is formed by H atoms combination or by an H atom abstracting hydrogen... 

One of the first fictional fluoropolymers was poly-1,2,2-trifluorostyrene. On one hand, it has much better oxidation and chemical resistance in comparison with common hydrocarbon polymers and, on the other hand, a wide range of functional groups can be attached to the aromatic ring. A sulfonated polymer was successfully used as a membrane for fuel cells by General Electric Co.3... 

Before fluorination, the dielectric constant ofpoly(bisbenzocyclobutene) was 2.8, and this value was reduced to 2.1 after plasma treatment. No data were reported in the paper on characterization of structure or properties, except for the dielectric constant of the modified poly(bisbenzocyclobutene). The authors did report that the thermal stability offluorinatedpoly(vinylidenefluoride) was inferior to the original poly(vinylidenefluoride) when treated in a similar way. One of the probable reasons for the low thermal stability is that the NF3 plasma degraded the polymer. According to their results, the thickness of fluorinated poly(bisbenzo-cyclobutene) was reduced by 30%. The same phenomenon was observed for other hydrocarbon polymers subjected to the NF3 plasma process. A remaining question is whether plasma treatment can modify more than a thin surface layer of the cured polymer Additionally, one of the side products generated was hydrogen fluoride, which is a serious drawback to this approach. 

Figure 18 shows the temperature dependence of the proton conductivity of Nafion and one variety of a sulfonated poly(arylene ether ketone) (unpublished data from the laboratory of one of the authors). The transport properties of the two materials are typical for these classes of membrane materials, based on perfluorinated and hydrocarbon polymers. This is clear from a compilation of Do, Ch 20, and q data for a variety of membrane materials, including Dow membranes of different equivalent weights, Nafion/Si02 composites ° ° (including unpublished data from the laboratory of one of the authors), cross-linked poly ary lenes, and sulfonated poly-(phenoxyphosphazenes) (Figure 19). The data points all center around the curves for Nafion and S—PEK, indicating essentially universal transport behavior for the two classes of membrane materials (only for S—POP are the transport coefficients somewhat lower, suggesting a more reduced percolation in this particular material). This correlation is also true for the electro-osmotic drag coefficients 7 20 and Amcoh...

Hydrocarbon polymers (HCP) are used not only as fuel components but also as binders of crystalline oxidizers and metal powders in the formulation of pyrolants, similar to composite propellants and plastic-bonded explosives. There are many types of HCP, the physicochemical properties of which are dependent on their molecular structures. The viscosity, molecular mass, and functionality of the poly-... 

Some of the most useful polyphosphazenes are fluoroalkoxy derivatives and amorphous copolymers (11.27) that are practicable as flame-retardant, hydrocarbon solvent- and oil-resistant elastomers, which have found aerospace and automotive applications. Polymers such as the amorphous comb polymer poly[bis(methoxyethoxyethoxy)phosphazene] (11.28) weakly coordinate Li " ions and are of substantial interest as components of polymeric electrolytes in battery technology. Polyphosphazenes are also of interest as biomedical materials and bioinert, bioactive, membrane-forming and bioerodable materials and hydrogels have been prepared. 

In 1938, while attempting to prepare fluorocarbon derivatives, Roy J. Plunkett, at DuPont s Jackson Laboratory, discovered that he had prepared a new polymeric material. The discovery was somewhat serendipitous as the TFE that had been produced and stored in cylinders had polymerized into poly(tetra-fluoroethylene) (PTFE), as shown in Eigure 4.2. It did not take long to discover that PTFE possessed properties that were unusual and unlike those of similar hydrocarbon polymers. These properties include (1) low surface tension, (2) high Tm, (3) chemical inertness, and (4) low coefficient of friction. All of these properties have been exploited in the fabrication of engineering materials, wliich explains the huge commercial success of PTFE. 

Spectra have been recorded of the following polymers Poly isobutylene. Schaufele has reported a spectrum of a non-turbid specimen of this material complete with depolarization data (18). Bands at Av - 2919 and 720 cm 1 are clearly polarized and must result from symmetrical modes. Schaufele was also able to show that the short chain hydrocarbon CH3(CH2)12CH3 could be examined satisfactorily but the results were very much sharpened by cooling to liquid air temperatures. Polyisoprene and Polybutadiene. Both of these in the cis form have also been examined at Southampton very recently. The trans isomers gave no spectra due to fluorescence but no interpretation has been attempted as yet. Spectra are shown in Fig. 7 and 8. 

The light-scattering behavior of those polysilanes studied indicates that they are slightly extended and stiffened compared with typical polyolefins. One measure of chain flexibility is the characteristic ratio C, which is also shown in the table. The values of C for most polysilanes of about 20 are larger than those for typical hydrocarbon polymers (—10), indicating that the polysilanes are somewhat less flexible than polyolefins. However, poly(diarylsilylene)s are much more rod-like and inflexible, with persistence lengths greater than 100 46... 

For the stabilization of various insoluble hydrocarbon polymers in carbon dioxide, it has been found that no one surfactant works well for all systems. Therefore it has become necessary to tailor the surfactants to the specific polymerization reaction. Through variation of not only the composition of the surfactants, but also their architectures, surfactants have been molecularly-engineered to be surface active—partitioning at the interface between the growing polymer particle and the CO2 continuous phase. The surfactants utilized to date include poly(FOA) homopolymer, poly(dimethylsiloxane) homopolymer with a polymerizable endgroup, poly(styrene-b-FOA), and poly(styrene-b-dimethylsiloxane). Through the utilization of these surfactants, the successful dispersion polymerization of methyl methacrylate (MMA), styrene, and 2,6-dimethylphenol in CO2 has been demonstrated. 

Elimination of carbon dioxide from carboxyl, water from alcoholic hydroxyl, carboxylic acid from alkanoate, and hydrogen chloride from chlorine side groups or chain ends are typical thermal decomposition reactions in the temperature range 250-350°C. Hydrogen chloride is an important product of poly(vinyl chloride) because every second carbon atom of the hydrocarbon polymer chain is chlorine substituted. But hydroxyl, alkanoate and free carboxylic acid groups normally occur only at the ends of the macromolecular chains in customary plastics, thus the contribution of their elimination to the volatile pyrolysis products is negligible. 

---