Hybrid membrane systems pervaporation -distillation system

For the study of the process, a set of partial differential model equations for a flat sheet pervaporation membrane with an integrated heat exchanger (see fig.2) has been developed. The temperature dependence of the permeability coefficient is defined like an Arrhenius function [S. Sommer, 2003] and our new developed model of the pervaporation process is based on the model proposed by [Wijmans and Baker, 1993] (see equation 1). With this model the effect of the heat integration can be studied under different operating conditions and module geometry and material using a turbulent flow in the feed. The model has been developed in gPROMS and coupled with the model of the distillation column described by [J.-U Repke, 2006], for the study of the whole hybrid system pervaporation distillation. 

On the other hand, a pervaporation membrane can be coupled with a conventional distillation column, resulting in a hybrid membrane/distillation process (228,229). Some of the investigated applications of such hybrid pervaporation membrane/distillation systems are shown in Table 9. In hybrid pervaporation/ distillation systems, the membrane units can be installed on the overhead vapor of the distillation column, as shown in Figure 13a for the case of propylene/ propane splitting (234), or they can be installed on the feed to the distillation column,... 

For the model validation and the analysis of the heat integration in the hybrid pervaporation distillation process, a laboratory plant has been built at the TU -Berlin and prepared for the connection with the distillation column (see fig. 3). With this plant experiments with a flat PVA-based (Polyvinylalcohol from GKSS) hydrophilic membrane have been done. A heat exchanger has been built within the pervaporation module. The temperature in the heat exchanger has been necessary to avoid the temperature drop between feed and retentate streams in the pervaporation process. In the process a 2-Propanol/ Water mixture has been separated. The concentration of 2-Propanol in the feed is between 80 and 90 % in weight and the temperature range in the experiments was between 70 and 90°C. The feed flow is turbulent and the system fully insulated to avoid heat looses. The pressure in the permeate side has been kept at 30 mbar and the feed pressure at 1.5 bar. 

Thus, theoretically, membrane technology may be the best candidate to couple reaction and separation. In the hterature, it is possible to find some hybrid units coupling the reliability of the reactive distillation system with the pervaporative technology when an esterification reaction is mn (Riemenschneider Bolt, 2000 Buchaly et al., 2012 Bida, Gongping, Xueliang, Wang, Wanqin, 2012). This allows for a reduction of energy consumption and an enhancement of process quality compared with stand-alone reactive distillation. 

Membranes can also be used to purify a mixmre and attain composition beyond the azeotropic composition. The pervaporation process features a liquid feed, a liquid retentate, and a vapor permeate. While gas-phase membrane processes are essentially isothermal, the phase change in the pervaporation process produces a temperature decrease as the retentate flows through the unit. Since flux rates decrease with decreasing temperature, the conventional pervaporation unit consists of several membrane modules in series with interstage heating. The vapor permeate must be condensed for recovery and recycle, and refrigeration is usually required. Hybrid systems of distillation columns and pervaporation units are frequently used in situations where distillation alone is impossible or very expensive. An important application is the removal of water from the ethanol-water azeotrope. Chapter 14 will discuss the details of design and control of such processes. 

The main problem in membrane processes, especially for UF and MF separations, is the decrease of permeate flux caused by concentration polarization and fouling, whereas other membrane processes such as gas separation and pervaporation are less affected. Different approaches have been studied to reduce fouling. Hybrid systems using different types of membrane operations (e.g., distillation, dialysis, NF, pervaporation, and osmosis) prevent microbial fouling, offering a strong potential for the use of new types of thin-film composite membranes. 

Daviou M. C., P. M. Hoch, and A. M. Eliceche, Design of membrane modules used in hybrid distillation/pervaporation systems, Ind. Engng. Chem. Res., 43, 3403-3412 (2004). 

---