Hot formation

Underground dry steam is relatively rare, but it is the most desirable from the standpoint of power generation. More commonly, energy reaches the surface as supeiheated water and steam. In some cases, the water is so pure that it can be used for irrigation and livestock in others, it is loaded with corrosive, scale-forming salts. Utilization of the heat from contaminated geothermal water generally requires that the water be reinjected into the hot formation after heat removal to prevent contamination of surface water. 

The utilization of hot dry rocks for energy requires fracturing of the hot formation, followed by injection of water and withdrawal of steam. This technology is still in the experimental state but promises approximately 10 times as much energy production as steam and hot water sources. 

Fluidized-bed catalytic reactors. In fluidized-bed reactors, solid material in the form of fine particles is held in suspension by the upward flow of the reacting fluid. The effect of the rapid motion of the particles is good heat transfer and temperature uniformity. This prevents the formation of the hot spots that can occur with fixed-bed reactors. 

In the refinery the salts deposit in the tubes of exchangers and reduce heat transfer, while in heater tubes, hot spots are created favoring coke formation. 

The second detergent function is to prevent formation of varnishes that come from polymerization of deposits on hot surfaces of the cylinder and the piston. Finally, by adsorption on metallic surfaces, these compounds have anti-corrosion effects. 

Strong oxidising acids, for example hot concentrated sulphuric acid and nitric acid, attack finely divided boron to give boric acid H3CO3. The metallic elements behave much as expected, the metal being oxidised whilst the acid is reduced. Bulk aluminium, however, is rendered passive by both dilute and concentrated nitric acid and no action occurs the passivity is due to the formation of an impervious oxide layer. Finely divided aluminium does dissolve slowly when heated in concentrated nitric acid. 

The formation of halatefV) and halide ions by reaction (11.4) is favoured by the use of hot concentrated solutions of alkali and an excess of the halogen. 

When concentrated sulphuric acid is added to ethanol, the mixture becomes hot owing to the formation of ethyl hydrogen sulphate, the yield of which is increased if the mixture is then gently boiled under reflux ... 

Lead formate is only slightly soluble in cold water, and insoluble in hot absolute ethanol it can therefore be readily distinguished from lead acetate or sugar of lead because, quite apart from chemical tests, the acetate is readily soluble in cold water and moderately soluble in ethanol. 

The reaction is readily illustrated by the formation of crystalline sorbic acid by the condensation of crotonaldehyde and malonic acid in hot pyridine solution ... 

Osazone formation. Forms an osazone, m.p. 206 (see however footnote, p. 140) this osazone, unlike glucosazone, is soluble in hot water. See p. 139 for preparation. Examine the crystals under the microscope and note the sheaves of plates, not needles (Fig. 63(B),... 

Osazone formation. Forms a yellow osazone, m.p. 208° soluble in hot water. See p. 137 for preparation. If examined under the microscope very characteristic clusters of hedge-hog crystals will be seen (Fig. 63(c), p. 139). The difference in the crystalline appearance of lactosazonc and maltosazone should be very carefully noted, as this difference forms the chief and most reliable method of differentiating between these two sugars. 

Make a concentrated solution of anthracene in hot acetone. To about 2 ml. of this solution add a cold concentrated acetone solution of picric acid drop by drop, and note the formation of a red coloration which becomes deeper on further addition of the acid. If excess of picric acid is added, however, the solution becomes paler in colour, and this is to be avoided if possible. Boil to ensure that both components are in solution and then transfer to a small porcelain basin or watch-glass ruby-red crystals of anthracene picrate separate out on cooling. The product, however, is often contaminated with an excess of either anthracene or of picric acid, which appear as yellowish crystals. 

The approximate times of osazone formation in minutes are given in Table 111,139. The product from mannose is the simple hydrazone and is practically white. Arabinose osazone separates first as an oil, whilst that from galactose is highly crystalline. Lactose and maltose give no precipitate from hot solution. 

Hydrochloric acid should not be used for acidifying the alkaline solution since the yellow colour, due to the ferric chloride formed, causes the Prussian blue to appear greenish. For the same reason, ferric chloride should not be added—as is frequently recommended a sufficient concentration of ferric ions is produced by atmospheric oxidation of the hot alkaline solution. The addition of a little dfiute potassium fluoride solution may be advantageous in assisting the formation of Prussian blue in a readily filterable form. 

METHOD 2 [128, 129]--To make dibromodioxane one stirs 500g dioxane in a flask which is in an ice bath, all of which is in the hood. 990g of liquid Bra is rapidly added, causing the solution to get hot (one can also bubble in an approximate amount of bromine from a gas canister). The solution is dumped into a bucket containing 2L of ice water, causing the immediate formation of a large mass of orange dibromodioxane crystals which are separated by vacuum filtration and dried. 

Carbanions stabilized by phosphorus and acyl substituents have also been frequently used in sophisticated cyclization reactions under mild reaction conditions. Perhaps the most spectacular case is the formation of an ylide from the >S-lactam given below using polymeric Hflnig base (diisopropylaminomethylated polystyrene) for removal of protons. The phosphorus ylide in hot toluene then underwent an intramolecular Wlttig reaction with an acetyl-thio group to yield the extremely acid-sensitive penicillin analogue (a penem I. Ernest, 1979). 

---