Hinge mount

For gas temperatures in excess of 380°C, experienced manufacturers often mount the adjustable guide vanes in special ceramic bearings. The shaft end of each blade is fixed to a lever, which is connected to a hinge-mounted adjusting cylinder. Axial movements of the cylinder open or close the blading. 

The small scale clos tester is a metal cup with a thermometer fitted below the bottom of the internal chamber with a hinge mounted cover having filling orifice. The sample is introduced to the cup and the cup is maintained at a constant temperature by means of temperature controller. After a specific time, a test flame is applied for 2.5 s and an observation is made whether or not flash has occurred. If flash did not occur the cup is cleaned, a new sample is introduced and the temperature is increased by 5 C. The measurements are repeated until the flash point is determined with accuracy of TC. 

Fig. 3.1. Experimental arrangement described by Kachi and Kon [3.33]. The CO2 pump laser cavity is formed by a mirror and a grating at the Littrow angle (autocollimation). Output coupling occurs via the zeroth order reflection from the grating. Note the hinge mount which ensures that the output beam is in a fixed direction for all wavelengths. The submillimeter laser resonator used here is of the Fabry-Perot type. A small amount of the radiation is coupled out to the detection system with a Michelson interferometer used to select the desired line when two or more lines oscillate. From [3.33]...

Continuous-type buckets (Fig. 21-5/) are generally back-mounted to chain or belt at close intervals. They are usually fabricated of steel. Style 5 is standard for normal materi s, with style 6 a low-front type for better discharge of difficult materials. Style 7 buckets are used for additional capacity or large lumps, and style 8 for inclined crusher-type elevators. Style 9 bu( ets are designed for extremely high capacities and are usually side-mounted and hinged together. 

Indicating instruments, lamps, pushbuttons, selector switches and reset knobs etc. are mounted on the trolley on a hinged auxiliary door, as shown in Figures... 

Although multiple-blade turbines are effective, two- and three-blade rotors are most cost-effective. Two-blade rotors commonly use teetering hinges, and all thrcc-bladc rotors arc mounted on rigid hubs. Rotors up to 15 m in diameter are economically fea-... 

The rigid urethane foam concept with integral skins has also found considerable interest in the automotive industry for exterior body parts, such as engine or trunk compartment lids, fenders and even full roofs. These parts can be reinforced with metal inserts where necessary or hinges and fasteners can be molded in for ready mounting. 

A few words should be said with respect to the principle of the measurement. In order to determine extinction positions, the plane of polarization of the incident beam is adjusted so that it coincides with the plane of incidence of the mirror (reflection prism). The analyzer, which is placed in the line of the horizontal beam A, is then crossed. This analyzer is placed on an arm, which extends from a vertical tube containing the polarizer. This tube is mounted revolvable around the incident beam. Handle in Fig. 6.6 is also connected with the said hinging arm, in order to make part V, which contains the mirror, rotating together with the polarizer. As a consequence, the planes of polarization and of incidence remain coincident during this rotation. No difficulties are encountered in this way with the determination of the extinction positions. A slight incon-... 

It was believed that mounting on 100 percent rag board with tape hinges would create an archival presentation for the image. It turns out that rag board absorbs and retains pollutants and will pass them on to a print. In a day No. But certainly well within the 100 years we hope to achieve. 

Proceeding from this, the photos show the mountings of such doors. These are a handle of round iron, two steel straps the width of the door (and bolted through the panel ) and on the hinge side supported by blocks lagscrewed into the door frame (this is the construction method for heavy door panels). At the swing side these straps are fitted with latchbolts that turn into catches made of band... 

Another hinged frame (Figure 266) was developed for a small scale laboratory machine.In addition, this design features a modified support system for the rollers by coasters running on hardened rings or completely sealed bearings mounted on the rollers, which makes it very easy to mount different roll types (Figures 267 and 268). 

Figure 267. Photograph of a small roller press showing one hinged frame member open for roller removal or mounting. (Courtesy of Bepex/Hutt, Leingarten, FRG)...

The reactor consists basically of two hemicylinders hinged together on a vertical side. The wire enters the reactor through a small aperture in the base and leaves the reactor through a similar aperture in the top. Six low-pressure mercury lamps (Southern New England Ultraviolet Co.) are mounted vertically and symmetrically inside the reactor. The principal emission ( 80%) from these lamps occurs at 254 nm. A principal emission at 300 or 350 nm is available from lamps constructed with the appropriate phosphors (Figure 4). The inside walls of the reactor are made reflecting to UV radiation by flexible, front-sided mirrors. The... 

If you ignore the mounting hinges, then doors are achiral. The plane of a door is a symmetry plane. 

---