Heat-affected zone corrosion

For both heat-affected zone corrosion (intergranular attack) and knifeline attack the heat flux during welding and the time at temperature can critically affect the severity of the attack. Both these factors may vary from one welder to another, and when preparing pieces for corrosion testing not only should fabrication welding conditions be accurately reproduced, but the work of more than one welder should be evaluated. 

Many instances of intergranular stress corrosion cracking (IGSCC) of stainless steel and nickel-based alloys have occurred in the reactor water systems of BWRs. IGSCC, first observed in the recirculation piping systems (21) and later in reactor vessel internal components, has been observed primarily in the weld heat-affected zone of Type 304 stainless steel. 

Zirconium is completely resistant to sulfuric acid up to Foiling temperatures, at concentrations up to 70 wt %, except that the heat-affected zones at welds have lower resistance in >55 wt % concentration acid (Fig. 1). Fluoride ions must be excluded from the sulfuric acid. Cupric, ferric, or nitrate ions significantly increase the corrosion rate of zirconium in 65—75 wt % sulfuric acid. 

Corrosive chemicals and external exposure can cause tank failure. Materials of construction should be chosen so that they are compatible with the chemicals and exposure involved. Welding reduces the corrosion resistance of many alloys, leading to localized attack at the heat-affected zones. This may be prevented by the use of the proper alloys and weld materials, in some cases combined with annealing heat treatment. 

Hastelloy C-4 is almost totally immune to selective intergranular corrosion in weld-heat-affected zones with high temperature stabihty in the 650-I040 C (I200-I900 F) range Hastelloy C-22 has better overall corrosion resistance and versatihty than either C-4 or C-276 (in most environments). 

The weld was riddled with mildly undercut, gaping pits. Attack was confined to fused and heat-affected zones, with a pronounced lateral or circumferential propagation (as in Fig. 6.10). The resulting perforation at the external surface was quite small. Pits were filled with deposits, friable oxides, and other corrosion products. Black plugs embedded in material filling the gaping pit contained high concentrations of iron sulfide. Bulk deposits contained about 90% iron oxide. Carbonaceous material was not detected. 

Stressed, such as heat-affected zones near welds, in areas of high acid-gas concentration, or at a hot gas-liquid interface. Therefore, stress-relieving all equipment after manufacturing is necessary to reduce corrosion, and special metallurgy in specific areas such as the still overhead or the reboiler tubes may be required. 

Selective corrosion in the heat-affected zone of a weld occurs most commonly when unstabilised stainless steels are used in certain environments. The obvious answer is to use an extra-low-carbon grade of stainless steel, e.g. types 304L, 316L or a stabilised grade of steel, e.g. types 321 and 347. Knifeline attack at the edge of a weld is not commonly encountered and is seldom predictable, and it must be hoped that it is revealed during preliminary corrosion testing. 

The heat-affected zone may become susceptible to stress-corrosion cracking, particularly the high-strength alloys, and expert advice is necessary... 

Known facts Possible Scenarios], Isopentane Pipe samples show external corrosion especially in heat affected zones Pressure indicator on system went up to 120 psig. Pipe samples found with split running along pipe Maintenance records indicate correct materiai and schedule used for repairs Area has clearly understood gasket chart... 

Measuring a wall thickness on the exterior of a vessel near a weld may not yield an accurate measurement. It is not uncommon for the worst internal corrosion to occur in weldor heat-affected zones. 

This method is the simplest of all the methods and is capable of detecting surface flaws such as corrosion, contamination, surface finish and surface discontinuities on joints.47 The discontinuities on joints such as welds, seals, solder connections and adhesive bonds can be detected. General corrosion, qualitative pitting corrosion, stress-corrosion cracking, weld-heat-affected zone attack, erosion corrosion and other type of degradation can be observed by visual examination aided by microscopes with sufficient magnification. Degradation of plastics can also be detected by visual examination. Visual examination is also used in conjunction with other techniques, such as powerful microscopes. 

Dealuminification occurs in aluminum bronzes containing the y-2 phase microstructure and the process is more severe when the y-2 phase forms a continuous grain boundary network. Dealuminification can be averted by rapid cooling from >600°C, or by addition of 1-2% iron or more than 4.5% nickel. Microstmctural changes can still occur during welding and lead to corrosion in the heat-affected zone. 

Welded microstructures can be extremely complex and often change drastically over a very short distance. The fusion zone or weld metal is a dendritic structure that has solidified from a molten state. Bordering the fusion zone are transition, unmixed and partially melted zones, and the heat-affected zone (HAZ). These zones can be reheated and altered by subsequent weld passes, in multipass welding. For alloys with structures that depend strongly on thermal history, such as steels, the final microstructure can be extremely complex. Since welded structures are often quite susceptible to corrosion, overalloyed filler metals are often used to enhance the weld corrosion resistance. For stainless steels with sufficiently high carbon content, sensitization in the HAZ is another major problem. (Frankel)5... 

Carbon steels. The corrosion behavior of carbon steel weldments produced by fusion welding can be due to metallurgical effects, such as preferential corrosion of the heat-affected zone (HAZ) or weld metal, or it can be associated with geometric aspects, such as stress concentration at the weld toe, or creation of crevices due to joint design. 

It has been shown that welds provide unique environments for the colonization of SRB with the subsequent production of sulfides that affect the weld seam surface of the heat-affected zone. Exposure of sulfide-derived surfaces to fresh, aerated seawater resulted in rapid spalling on the downstream side of weld seams. The bared surfaces became anodic to the sulfide-coated weld root, initiating and accelerating localized corrosion. (Dexter)5... 

---