Polyethylene glass transition temperature

Carbon Cha.in Backbone Polymers. These polymers may be represented by (4) and considered derivatives of polyethylene, where n is the degree of polymeriza tion and R is (an alkyl group or) a functional group hydrogen (polyethylene), methyl (polypropylene), carboxyl (poly(acryhc acid)), chlorine (poly(vinyl chloride)), phenyl (polystyrene) hydroxyl (poly(vinyl alcohol)), ester (poly(vinyl acetate)), nitrile (polyacrylonitrile), vinyl (polybutadiene), etc. The functional groups and the molecular weight of the polymers, control thek properties which vary in hydrophobicity, solubiUty characteristics, glass-transition temperature, and crystallinity. 

Plasticizers and Processing Aids. Petroleum-based oils are commonly used as plasticizers. Compound viscosity is reduced, and mixing, processing, and low temperature properties are improved. Air permeabihty is increased by adding extender oils. Plasticizers are selected for their compatibihty and low temperature properties. Butyl mbber has a solubihty parameter of ca 15.3 (f /cm ) [7.5 (cal/cm ) ], similar to paraffinic and naphthenic oils. Polybutenes, paraffin waxes, and low mol wt polyethylene can also be used as plasticizers (qv). Alkyl adipates and sebacates reduce the glass-transition temperature and improve low temperature properties. Process aids, eg, mineral mbber and Stmktol 40 ms, improve filler dispersion and cured adhesion to high unsaturated mbber substrates. 

Inclusion of double bonds will stiffen the chain at the point of inclusion but at the same time may increase the flexibility of adjacent bonds. The net effect may therefore be to reduce the glass transition temperature and this appears to occur in 1,4-polybutadiene when compared with polyethylene. 

With plastics there is a certain temperature, called the glass transition temperature, Tg, below which the material behaves like glass i.e. it is hard and rigid. As can be seen from Table 1.8 the value for Tg for a particular plastic is not necessarily a low temperature. This immediately helps to explain some of the differences which we observe in plastics. For example, at room temperature polystyrene and acrylic are below their respective Tg values and hence we observe these materials in their glassy state. Note, however, that in contrast, at room temperature, polyethylene is above its glass transition temperature and so we observe a very flexible matoial. When cooled below its Tg it then becomes a hard, brittle solid. Plastics can have several transitions. 

The most common backbone structure found in commercial polymers is the saturated carbon-carbon structure. Polymers with saturated carbon-carbon backbones, such as polyethylene, polypropylene, polystyrene, polyvinyl chloride, and polyacrylates, are produced using chain-growth polymerizations. The saturated carbon-carbon backbone of polyethylene with no side groups is a relatively flexible polymer chain. The glass transition temperature is low at -20°C for high-density polyethylene. Side groups on the carbon-carbon backbone influence thermal transitions, solubility, and other polymer properties. 

In contrast to the applications previously described in which alkanesulfonates are used in polymers with a high glass transition temperature (PVC, polystyrene, and ABS), in antistatic-modified polyethylene articles the antistatic agent is able to continue migrating to the surface over a long period of time. Thus, a more permanent antistatic effect is achieved. 

The flow of liquid hydrocarbons can be enhanced by introducing into the stream a nonagglomerating suspension of ultra-high molecular weight polyethylene [490,1647] in water with small amounts of surfactant. The finely divided polyethylene is prepared by polymerization and then cryogrinded below the glass-transition temperature. 

Composite-based PTC thermistors are potentially more economical. These devices are based on a combination of a conductor in a semicrystalline polymer—for example, carbon black in polyethylene. Other fillers include copper, iron, and silver. Important filler parameters in addition to conductivity include particle size, distribution, morphology, surface energy, oxidation state, and thermal expansion coefficient. Important polymer matrix characteristics in addition to conductivity include the glass transition temperature, Tg, and thermal expansion coefficient. Interfacial effects are extremely important in these materials and can influence the ultimate electrical properties of the composite. 

Linear polyethylene (hdpe), which has a repeating unit of 4-CHr CH24 , is a typical thermoplastic with a glass transition temperature Tt below room temperature. Its mechanical properties permit its use as both a plastic and a fiber. From a structural viewpoint, this polymeric hydrocarbon is the least complex of all polymers. 

---