Polyethylene modifiers

DuPont Acetal EVA Nylon 6, 6/6, 6/12, Mineral Filled 6/6, Industrial PBT PET Polyethylene Modified Thermoplastic Elastomer Ionomer Liquid Crystal Polymer ... 

Figure 5. Fluorescence of collagen IV conjugated with Oregon Green 488 (Molecular Probes, Eugene, OR, USA.) spontaneously adsorbed to unmodified polyethylene foils (A) or polyethylene modified with 1014 0+ ions/cm at the energy of 30 keV (B). Collagen was diluted in phosphate-buffered saline to the concentration of 0.02 mg/ml (10 pg/cm ) and incubated with the foils for 24 h at room temperature. For auto fluorescence control.

Table 18. Thromboresistance of polyethylene modified with heparin and trypsin 137)...

LDPE-starch Polyethylene modified with starch... 

Munoz PMP et al. (2001) High-density polyethylene modified by polydimethyl silox-ane. J Appl Poly Sci 82(14) 3460-3467... 

It is shown that the applicability of fractal model of anomalous diffusion for quantitative description of thermogravimetric analysis results in case of high density polyethylene modified by high disperse mixture Fe/FeO (Z). It is shown the influence of diffusion type on the value of sample 5%-th mass loss temperature and was offered structural analysis of this effect. The critical content Z it is determined, at which degradation will be elapse so, as in inert gas atmosphere. 

BIODEGRADATION OF POLYETHYLENE MODIFIED WITH BIONOLLE POLYESTER... 

Chem. Descrip. Micronized polyethylene-modified PTFEwax CAS 9002-84-0 EINECS/ELINCS 204-126-9 Uses Abrasion resistance aid tor surtace coatings, can and coil coatings, one-coat applies., printing inks metal marking resistance aid in pigments and malted systems... 

Chem. Descrip. Polyethylene-modified polypropylene wax Uses Surf, modifier, scratch resist, aid, scuff resist, aid, metal mark resist. aid, antiblocking agent for baking and air-dry coatings and inks, esp. can and coil coatings, plastics food-contact coatings Regulatory FDA 21 CFR 175.300... 

Vasilkov, A., Naumkin, A., Nikitin, L. Volkov, L, Podshibikhin, V, and Lisichkm, G. Ul-trahigh molecular weight polyethylene modified with silver nanoparticles prepared by metal-vapour synthesis. AIP Conference Proceedings., 1042,255-257 (2008). 

Chlorinated polyethylene (CPE) n. Any polyethylene modified by simple chemical substitution of chlorine on the hnear backbone chain, CPEs range from rubbery amorphous elastomers at 35-40% Cl to hard, semicrystalline materials at 68-75% Cl. They are sometimes included with chlorinated natural and butyl rubbers under the term chlorinated rubbers. Certain CPEs are used as modifiers in PVC compounds to obtain better flexibihty and toughness, particularly low-temperature toughness, greater latitude in compounding, and ease of processing. 

Chlorinated polyethylene (CPE). Chlorinated polyethylene modifiers are most commonly used in pipe, fittings, siding, and weatherable profiles. CPE modifiers compete primarily with acrylics in siding applications. CPE can be used in resins other than PVC, for example, PE and PP. 

An inorganic impact modifier has been marketed by the Norwegian waste recovery company, Elkem Materials. It is called Sidistar and made of amorphous silica spheres with a median particle size of about 150 nm. They are derived from the silica fume accumulating during the manufacture of ferro-silicon alloys and silicon metal. Elkem claim that their silica modifiers can impart good impact strength at low temperatures in thermoplastic pipe, and can replace conventional acrylic, MBS and chlorinated polyethylene modifiers. 

H. Czarczynska and W. Trochimczuk, Changes the Structure of Chloromethylated Polyethylene Modified with Styrene and Divinylbenzene Foils due to Friedel-Crafts Catalysts, J. Polym. Sci. 47C, 111 (1974). Semi-II IPNs and IPNs. Chloromethylated structures as points of crosslinking. Effects of AICI3, ZnCl2, and SnCU as catalysts. Optical microscopy of phase separation. 

Fig. 28 Modification in oxidation induction time (filled circle) and oxidation rate (filled square) as the effect of degradation induced by EB irradiation in polyethylene modified with Ti02 nanoparticles (0.5 wt%). Temperature 200 °C. Environment air. The data were taken from [95J1].

C. Manzi-Nshuti, J. M. Hossenlopp, and C. A. Wilkie, Comparative study on the flammability of polyethylene modified with commercial fire retardants and a zinc aluminum oleate layered double hydroxide. Polymer Degradation and Stability, 94 (2009), 782-8. 

Machukov, N. I., Gladyshev, G. R, Kozlov, G. V. (1991)l Stracture and Properties of High Density Polyethylene Modified by High-Disperse Mixture Fe and FeO. Vysoko-molek. Soed. A, 33(12), 2538-2546. 

BIODEGRADABLE POLYMER FILMS ON LOW DENSITY POLYETHYLENE, MODIFIED CHITOSAN... 

Biodegradability of polyethylenes modified by TDPA and Envirocare additives has been assessed by a variety of laboratory-scale and field-scale composting tests. Most recently, an extensive commercial-scale composting trial of TOP A additives has been carried out in the municipal composting plant of Vienna Neustadt, Austria, directed by Dr. B. Raninger (Leoben University). 

The pure polyethylene modified with fluorine and oxygen is much stiffer than the other polyethylene controls the modulus at approximately 5.55% montmorillonite loading was significantly higher (about 1.9 GPa) compared with HDPE (0.768 GPa at 5.2% loading) and HDPE-g-MA (approximately 1.4 GPa at 4.97% loading). The authors point out legitimately that an optimization of the modification of the polyethylene with... 

Li,Y.R, Li, S.Y, Shi,W, Lei, M.K., 2012. Hydrophobic over-recovery during aging of polyethylene modified by oxygen capacitively coupled radio frequency plasma a new approach for stable superhydrophobic surface with high water adhesion. Surf. Coat. Technol. 206. 

Figure 27 Heat release curves of polyethylene modified with DECA, AO, and ZnAl-LDH. Reprinted from Manzi-Nshuti, C. Hossenlopp, J. M. Wilkie. C. A. Polym. Degrad. Stab. 2009, 94 (5), 782, with permission from Elsevier.

---