Glass transition temperature polyester resin

This type of adhesive is generally useful in the temperature range where the material is either leathery or mbbery, ie, between the glass-transition temperature and the melt temperature. Hot-melt adhesives are based on thermoplastic polymers that may be compounded or uncompounded ethylene—vinyl acetate copolymers, paraffin waxes, polypropylene, phenoxy resins, styrene—butadiene copolymers, ethylene—ethyl acrylate copolymers, and low, and low density polypropylene are used in the compounded state polyesters, polyamides, and polyurethanes are used in the mosdy uncompounded state. 

Differential scanning calorimetry (DSC) is fast, sensitive, simple, and only needs a small amount of a sample, therefore it is widely used to analyze the system. For example, a polyester-based TPU, 892024TPU, made in our lab, was blended with a commercial PVC resin in different ratios. The glass transition temperature (Tg) values of these systems were determined by DSC and the results are shown in Table 1. 

Keywords mechanical properties, polymer mortar, unsaturated polyester resin, recycled PET, degree of unsaturation, glass transition temperature. 

Various UPE resins based on recycled poly ethylene terephthalate(PET) were prepared and the properties of the polymer mortar made with the UPE as well as those of the cured resin itself were investigated. It was found that degree of unsaturation of the resins was the most important property affecting thermal and mechanical properties of the cured resin and PM. The cured unsaturated polyester resin or polymer mortar made from resins of higher unsaturation, i.e., less PET content or adipic acid content in the resin, showed higher glass transition temperatures,... 

Glass Transition Temperature. The of saturated polyester resins can be varied by a suitable choice of aromatic or aliphatic raw materials. The of nonplasticized... 

One method used to evaluate the upper working temperature of block copolymer systems is to measure the shear adhesion failure temperature (SAFT), a useful method to discover exactly what has been gained in the upper working temperature limits when resins are added to the styrene domain of polystyrene end-block systems to increase the effective glass transition temperature. Typically the test is set up as a standard shear test, either to the standard stainless steel panel or to polyester, with a 1 in. by 1 in. (25 mm by 25 mm) area and a load of 1 kg. The set-up is placed in an oven that can be accurately controlled so that the temperature is increased by 2.0°C (3.6°F) per minute, the temperature at which failure occurs being recorded as the SAFT. 

The hardening of the boundary layer of epoxy and polyester compositions was studied by IR spectroscopy (of repeatedly disturbed total internal reflection—RDTIR) on a UR-20 spectrometer. A KRS-5 prism N =18, C = 45°) and a germanium prism N =14, C = 45°) were used for simulation of the substrate surface. The thickness of a polymer layer was 0.5-1 nm for the element made of germanium and 2-3 nm for KRS-5. Inhibition of polyester resin polymerization by atmospheric oxygen was eliminated by applying a polyethylene film to the surface of a system to be hardened. The thickness of the applied epoxy and polyester composition was up to 20-30 nm. To evaluate the glass-transition temperature and the polymer-solvent interaction parameter, we used reversed-phase gas chromatography. Basalt-1 and basalt-2 (see below) served as fillers and as a model substrate. The... 

Vinyl ester resins are similar to unsaturated polyester resins in that they are cured by a free radical initiated polymerisation. However, they differ from the polyesters in that the unsaturation is at the ends of the molecule rather than along the polymer chain. Unlike polyesters, vinyl esters show a greater resistance to hydrolysis as well as lower peak exotherm temperatures and less shrinkage upon cure. Cured vinyl ester resins exhibit excellent resistance to acids, bases and solvents. They also show improved strain to failure, toughness and glass transition temperatures over polyesters. They can be used in filament winding, pultrusion, resin injection, vacuum moulding and conventional hand lay-up. 

---