Glass thermal expansion coefficients

Glass has a very low thermal expansion coefficient the materials joined with glass have to be similar in expansion or must be duetile, while staying vacuum tight. Even with best-matched materials skilled craftsmanship is asked for the joining process. 

Thermal Properties. Many commercial glass-ceramics have capitalized on thek superior thermal properties, particularly low or zero thermal expansion coupled with high thermal stabiUty and thermal shock resistance properties that are not readily achievable in glasses or ceramics. Linear thermal expansion coefficients ranging from —60 to 200 x 10 j° C can be obtained. Near-zero expansion materials are used in apphcations such as telescope mirror blanks, cookware, and stove cooktops, while high expansion frits are used for sealing metals. 

The viscosity of liquid silicates such as drose containing barium oxide and silica show a rapid fall between pure silica and 20 mole per cent of metal oxide of nearly an order of magnitude at 2000 K, followed by a slower decrease as more metal oxide is added. The viscosity then decreases by a factor of two between 20 and 40 mole per cent. The activation energy for viscous flow decreases from 560 kJ in pure silica to 160-180kJmol as the network is broken up by metal oxide addition. The introduction of CaFa into a silicate melt reduces the viscosity markedly, typically by about a factor of drree. There is a rapid increase in the thermal expansivity coefficient as the network is dispersed, from practically zero in solid silica to around 40 cm moP in a typical soda-lime glass. 

An additional check is the almost coincidence of the linear thermal expansion coefficients of the composite in the glassy region. Theory yields acl = 48.20 x 10-6 °C whereas experiment gives ac, = 48.00x 10 6 °C 1. This coincidence does not hold beyond glass transition. Indeed it was found that ot = 122.90 x 10-6 °C, whereas the experiment gave a 2 = 158 x 10"6 °C 1. 

As a consequence, the overall penetrant uptake cannot be used to get direct informations on the degree of plasticization, due to the multiplicity of the polymer-diluent interactions. The same amount of sorbed water may differently depress the glass transition temperature of systems having different thermal expansion coefficients, hydrogen bond capacity or characterized by a nodular structure that can be easily crazed in presence of sorbed water. The sorption modes, the models used to describe them and the mechanisms of plasticization are presented in the following discussion. 

The glass transition temperature of a dilute system, according to the free volume changes, is determined by the diluent volume fraction Vd, and changes of the thermal expansion coefficient, a, at Tg by using ... 

Network properties and microscopic structures of various epoxy resins cross-linked by phenolic novolacs were investigated by Suzuki et al.97 Positron annihilation spectroscopy (PAS) was utilized to characterize intermolecular spacing of networks and the results were compared to bulk polymer properties. The lifetimes (t3) and intensities (/3) of the active species (positronium ions) correspond to volume and number of holes which constitute the free volume in the network. Networks cured with flexible epoxies had more holes throughout the temperature range, and the space increased with temperature increases. Glass transition temperatures and thermal expansion coefficients (a) were calculated from plots of t3 versus temperature. The Tgs and thermal expansion coefficients obtained from PAS were lower titan those obtained from thermomechanical analysis. These differences were attributed to micro-Brownian motions determined by PAS versus macroscopic polymer properties determined by thermomechanical analysis. 

Since the glass transition corresponds to a constant value of the relaxation time [15], dTjdP is just the pressure coefficient of Tg. Comparing Equations 24.10 and 24.13, we see that the scaling exponent is related to quantities—thermal pressure coefficient, thermal expansion coefficient, Tg, and its pressure coefficient—that can all be determined from PVT measurements... 

The glass disc to be sealed into a tube must be made of glass having the same thermal expansion coefficient as the tube. Discs of different porosities can be obtained they consist of a large number of particles of glass sintered together so that numerous channels remain. When... 

Many different substrates are used fora-Si H deposition. Usually Corning 7059 glass [390] and crystalline silicon are used for materials research, as both have similar thermal expansion coefficients to fl-Si H. Devices are mostly made on... 

Introduction of Organic Network Modifiers. The introduction of organic network modifiers into SiO glasses leads to drastic changes of properties. SiO glass, for example, has a thermal expansion coefficient of about 0.5 10 K, monomethyl-SiO glass ([ch SiO. A ) about 100 10 K (40). 

---