Fluorides, NMR

In addition to providing relative reactivity information about aryl fluorides, NMR can be used to calculate the Taft substituent parameters Oj and Or (27-29) (see Table 3). 

Analytical Procedures. Oxygen difluoride may be determined conveniently by quantitative appHcation of k, nmr, and mass spectroscopy. Purity may also be assessed by vapor pressure measurements. Wet-chemical analyses can be conducted either by digestion with excess NaOH, followed by measurement of the excess base (2) and the fluoride ion (48,49), or by reaction with acidified KI solution, followed by measurement of the Hberated I2 (4). 

Pubhcations have described the use of HFPO to prepare acyl fluorides (53), fluoroketones (54), fluorinated heterocycles (55), as well as serving as a source of difluorocarbene for the synthesis of numerous cycHc and acycHc compounds (56). The isomerization of HFPO to hexafluoroacetone by hydrogen fluoride has been used as part of a one-pot synthesis of bisphenol AF (57). HFPO has been used as the starting material for the preparation of optically active perfluorinated acids (58). The nmr spectmm of HFPO is given in Reference 59. The molecular stmcture of HFPO has been deterrnined by gas-phase electron diffraction (13). 

Poly(vinyl fluoride) [24981-14-4] (PVF) is a semicrystaltiae polymer with a planar, zig-zag configuration (50). The degree of crystallinity can vary significantly from 20—60% (51) and is thought to be primarily a function of defect stmctures. Wide-line nmr and x-ray diffraction studies show the unit cell to contain two monomer units and have the dimensions of a = 0.857 nm, b = 0.495 nm, and c = 0.252 nm (52). Similarity to the phase I crystal form of poly (vinytidene fluoride) suggests an orthorhombic crystal (53). 

Unlike most crystalline polymers, PVDF exhibits thermodynamic compatibiUty with other polymers (133). Blends of PVDF and poly(methyl methacrylate) (PMMA) are compatible over a wide range of blend composition (134,135). SoHd-state nmr studies showed that isotactic PMMA is more miscible with PVDF than atactic and syndiotactic PMMA (136). MiscibiUty of PVDF and poly(alkyl acrylates) depends on a specific interaction between PVDF and oxygen within the acrylate and the effect of this interaction is diminished as the hydrocarbon content of the ester is increased (137). Strong dipolar interactions are important to achieve miscibility with poly(vinyhdene fluoride) (138). PVDF blends are the object of many papers and patents specific blends of PVDF and acryflc copolymers have seen large commercial use. 

S-Alkylthiiranium salts, e.g. (46), may be desulfurized by fluoride, chloride, bromide or iodide ions (Scheme 62) (78CC630). With chloride and bromide ion considerable dealkylation of (46) occurs. In salts less hindered than (46) nucleophilic attack on a ring carbon atom is common. When (46) is treated with bromide ion, only an 18% yield of alkene is obtained (compared to 100% with iodide ion), but the yield is quantitative if the methanesulfenyl bromide is removed by reaction with cyclohexene. Iodide ion has been used most generally. Sulfuranes may be intermediates, although in only one case was NMR evidence observed. Theoretical calculations favor a sulfurane structure (e.g. 17) in the gas phase, but polar solvents are likely to favor the thiiranium salt structure. 

Fluoride ion attacks the sulfur atom in 2,3-diphenylthiirene 1,1-dioxide to give ck-1,2-diphenylethylenesulfonyl fluoride (23%) and diphenylacetylene (35%). Bromide or iodide ion does not react (80JOC2604). Treatment of S-alkylthiirenium salts with chloride ion gives products of carbon attack, but the possibility of sulfur attack followed by addition of the sulfenyl chloride so produced to the alkyne has not been excluded (79MI50600). In fact the methanesulfenyl chloride formed from l-methyl-2,3-di- -butylthiirenium tetrafluoroborate has been trapped by reaction with 2-butyne. A sulfurane intermediate may be indicated by NMR experiments in liquid sulfur dioxide. 

Generation of benzocyclobutadiene by fluoride-induced eUmination has permitted the NMR spectmm to be observed under flow conditions. ... 

Tetrabutylammonium fluoride trihydrate (Aldnch) is heated in a round-bottom flask with magnetic stirring at 40-45 C under vacuum (<0.1 mm of Hg) After several hours, the sample liquefies. Heating is continued until the sample loses 20% of its original weight (usually ca 48 h). The resulting anhydrous TBAF (singlet at -99 ppm, F NMR) contains 0 1-03 molar equivalent of water (by NMR) and ca 10% tetrabutylammonium bifluoride (a doublet at -146 ppm, (J = 123 Hz, F NMR) This oil must be used immediately. 

Chemical shifts for F and nmr signals for Cl and Cl first observed 1962 CIF5 (the last halogen fluoride to be made) synthesized by W. Maya... 

There is also clear evidence of a change from predominantly class-a to class-b metal charactristics (p. 909) in passing down this group. Whereas cobalt(III) forms few complexes with the heavier donor atoms of Groups 15 and 16, rhodium(III), and more especially iridium (III), coordinate readily with P-, As- and S-donor ligands. Compounds with Se- and even Te- are also known. Thus infrared. X-ray and nmr studies show that, in complexes such as [Co(NH3)4(NCS)2]" ", the NCS acts as an A -donor ligand, whereas in [M(SCN)6] (M = Rh, Ir) it is an 5-donor. Likewise in the hexahalogeno complex anions, [MX ] ", cobalt forms only that with fluoride, whereas rhodium forms them with all the halides except iodide, and iridium forms them with all except fluoride. 

In the absence of water molecules in the system, similar compositions of fluoride complexes of tantalum and niobium are expected. An analysis of the 19F and 93Nb NMR spectra of solutions based on anhydrous hydrogen fluoride, performed by Buslaev et al., revealed the presence of NbF6 and NbF72 complexes [57]. 

NMR, Raman and IR spectroscopy are most frequently used to investigate the complex structures of fluoride solutions containing tantalum and niobium. Most investigations of such solutions were performed on the liquid-liquid extraction of tantalum and niobium, with the objective of describing the mechanism of the process. These publications will be discussed separately. 

As an example, an NMR spectrum of a 1,3-dioxolane-/3-propiolactone copolymer, obtained by using a boron-fluoride catalyst, is shown in Fig. 1101. The 1,3-dioxolane (DOL) homopolymer spectrum contains two singlet peaks of area 1 2 numbered 1 and 5, whereas the spectrum of the 0-propiolactone (PL) homopolymer contains two triplet peaks of area 1 1 numbered 2 and 6. Variation of initial feed ratios disclosed that peaks 1,3 and S are associated with the DOL units and that... 

The ratio of the different isomeric products was found to vary with time, temperature, and initial concentration. This suggested that some kind of equilibration was occurring between isomers. I3C NMR spectroscopy of a reaction mixture showed, upon cooling, the reversible formation of a pair of signals in the anomeric region. These signals were ascribed to the anomeric carbon atoms of fructofuranosyl fluorides (10), which were presumed to be in equilibrium with the reactive fructofuranosyl cation, 11. 

---