Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Fine grits

Abrade Hand abrade with Scotch-Brite wet with MEK until the surface is shiny. Use fine-grit, dry Scotch-Brite - pads on high-speed grinder driven by dry. oil-free N2 until the surface is shiny. [Pg.973]

Fig. 4. Malt mill with six rollers and shaking screens (1 = flour 2 = husks 3 = fine grits and, 4 = coarse grain). Fig. 4. Malt mill with six rollers and shaking screens (1 = flour 2 = husks 3 = fine grits and, 4 = coarse grain).
When the final layer is dry, sand the gesso surface using fine-grit sandpaper. [Pg.129]

Chemical Methods. Sherds were prepared for analysis by removing surface glazing and designs with a fine-grit silicon carbide abrasive paper. [Pg.131]

The equation was found to be in reasonable accord with the results from a series of tests using TNT, RDX, and HMX in various admixtures of fine grits. Whether the equation can be applied to primary explosives is not known. [Pg.137]

The discharge probe is cleaned after each test with fine grit emery paper and the sample holder is cleaned after each test series. [Pg.408]

The key to fast electrode equilibration with the skin is removing or abrogating the skin comeum. This is usually performed by skin abrasion. Fine-grit abrasive materials are sometimes incorporated into conunercial electric coupling creams so that outer layers of dead skin will be removed on... [Pg.414]

Carbon Degrease with solvent Abrade with fine-grit emery paper Repeat degreasing. Ensure all solvent has evaporated before bonding... [Pg.87]

Cellulose plastics Degrease with methyl alcohol, or isopropyl alcohol Roughen the surface with fine-grit emery paper Repeat degreasing If using epoxies, heat plastics for 1 hour at 93°C (200°F) and apply adhesive while still warm N.B. follow manufacturers instructions to avoid premature curing of epoxy adhesives... [Pg.87]

Plaster If plaster is fresh, allow to dry thoroughly Smooth the surface with fine-grit emery paper Remove all dust before applying adhesives... [Pg.89]

Super finishing hones Fine-grit grinding wheels... [Pg.295]

ARAMID XNBR HNBR Heat and fluids to >170 °C Cilbond 89 Cilbond 22 Abrade or grit blast with fine grit. Degrease with MEK Prebake first thin coat of primer at >100 °C use Cilbond 22 for PV bonding... [Pg.39]

Stress relieving heat treatments of the runner and discs must be specified at stages during manufacture. It is interesting to note that even the fine grit blasting operation to prepare the taper-land disc blanks for coating, can, unless carefully controlled, result in unacceptable distortion. [Pg.136]

The fine grit prodnced by the BTA Grit Removal System. [Pg.544]

Using fine-grit emery paper, remove any tarnish from bonding area. [Pg.83]

Abrade using fine-grit emery paper or gritblast. [Pg.86]

Carbon Degrease with acetone or MEK. Abrade using fine-grit emeiy paper. Repeat degreasing step. Allow solvent to evaporate. [Pg.90]

Sandpaper. Common aluminum oxide sandpaper runs from the coarse grit of P12 to the fine grit of P220 (and even higher for finish papers). Usually you U use a coarse paper first and finish with a finer grit, so it s worth buying a set. [Pg.216]


See other pages where Fine grits is mentioned: [Pg.308]    [Pg.416]    [Pg.255]    [Pg.128]    [Pg.109]    [Pg.323]    [Pg.29]    [Pg.29]    [Pg.87]    [Pg.87]    [Pg.682]    [Pg.353]    [Pg.14]    [Pg.750]    [Pg.13]    [Pg.96]    [Pg.159]    [Pg.167]    [Pg.25]    [Pg.602]    [Pg.603]    [Pg.206]    [Pg.258]    [Pg.85]    [Pg.24]    [Pg.28]    [Pg.181]    [Pg.79]    [Pg.91]    [Pg.243]   
See also in sourсe #XX -- [ Pg.191 ]




SEARCH



Grits

© 2024 chempedia.info