Tensile strength, fabric

Test Methods. Fabric Tensile Strength Samples were c iditioned at 21 + 2°C and 65 + 2% relative humidity. Tensile strength was measured on an instron CRE machine according to ASTM method D-1628 (Breaking load and elongation of textiles -grab test) (9). 

Polymerisation of a diol with a dicarboxybe acid is exemplified by the production of a polyester from ethylene glycol and terephthabc acid either by direct esterification or by a catalysed ester-interchange reaction. The resulting polyester (Terylene) is used for the manufacture of fibres and fabrics, and has high tensile strength and resibency its structure is probably ... 

Combination Flame Retardant—Durable Press Performance. Systems using THPC, urea, and TMM can be formulated to give fabrics which combine both flame-retardant performance and increased wrinkle recovery values (80). Another system employs dimethylol cyanoguanidine with THPC under acidic conditions (115). Both of these systems lead to substantial losses in fabric tensile and tearing strength. 

Weathering. Articles fabricated from FEP are unaffected by weather, and thek resistance to extreme heat, cold, and uv kradiation suits them for apphcations in radar and other electronic components. For example, after 15 years of solar exposure in Florida, the tensile strength (73) and light transmission (96%) of a 25-p.m thick film was unchanged and the film remained crystal clear. Elongation increased slightly for the first 5 to 7 years of outdoor exposure, probably as a result of stress relaxation. Beyond 10 years, a small decrease was observed. 

Modified ETEE is less dense, tougher, and stiffer and exhibits a higher tensile strength and creep resistance than PTEE, PEA, or EEP resins. It is ductile, and displays in various compositions the characteristic of a nonlinear stress—strain relationship. Typical physical properties of Tef2el products are shown in Table 1 (24,25). Properties such as elongation and flex life depend on crystallinity, which is affected by the rate of crysta11i2ation values depend on fabrication conditions and melt cooling rates. 

Polyester. This fiber has several performance advantages versus polypropylene, although it is less economical. Polyester can produce higher tensile strength and modulus fabrics that are dimensionally stable at higher temperatures than polypropylene. This is of importance in selected appHcations such as roofing. Polyester fabrics are easily dyed and printed with conventional equipment which is of extreme importance in apparel and face fabrics although of lesser importance in most spunbonded appHcations (see Fibers, polyester). 

The most important properties of refractory fibers are thermal conductivity, resistance to thermal and physical degradation at high temperatures, tensile strength, and elastic modulus. Thermal conductivity is affected by the material s bulk density, its fiber diameter, the amount of unfiberized material in the product, and the mean temperature of the insulation. Products fabricated from fine fibers with few unfiberized additions have the lowest thermal conductivities at high temperatures. A plot of thermal conductivity versus mean temperature for three oxide fibers having equal bulk densities is shown in Figure 2. 

Cured sihcone LIM mbber can be fabricated with physical properties equivalent to heat-cured mbber (385). Shore A hardness can range from 30 to 70, depending on formulations. Typical physical properties include tensile strengths as high as 9.7 MPa (1400 psi), 500—775% elongation at break, and tear strength of >30 N/mm (180 Ib/in.). Compression sets of less than 10% can be achieved if the material is baked after processing. 

The molecular orientation of the polymer in a fabricated specimen can significantly alter the stress—strain data as compared with the data obtained for an isotropic specimen, eg, one obtained by compression mol ding. For example, tensile strengths as high as 120 MPa (18,000 psi) have been reported for PS films and fibers (8). PS tensile strengths below 14 MPa (2000 psi) have been obtained in the direction perpendicular to the flow. 

Stress—Strain Curve. Other than the necessity for adequate tensile strength to allow processibiUty and adequate finished fabric strength, the performance characteristics of many textile items are governed by properties of fibers measured at relatively low strains (up to 5% extension) and by the change ia these properties as a function of varyiag environmental conditions (48). Thus, the whole stress—strain behavior of fibers from 2ero to ultimate extension should be studied, and various parameters should be selected to identify characteristics that can be related to performance. 

---