Ethylene-propylene-diene elastomers

Codimerization of ethylene and 1,3-butadiene is also of commercial significance since the product 1,4-hexadiene is used as a comonomer in the manufacture of ethylene-propylene-diene elastomers. Rhodium and nickel catalysts are used since they are the most active and selective, bringing about the formation of the required... 

Many other reports have demonstrated the smoke suppressing tendencies of hydrated fillers in various polymers including ethylene-propylene-diene elastomers,43 PP,38 polystyrene,49 modified polyphenylene oxide, polybutylene terephthalate, and ABS.37 In addition to suppressing smoke generation, a delay in the onset of smoke evolution is also achievable.25 Figure 7.5 illustrates smoke reductions obtained in PP. 

Low-temperature solution processes are state-of-the-art for the production of ethylene/propylene or ethylene/propylene/diene elastomers (EPDR or EPDM). A continuous stirred-tank reactor (CSTR) or a series of two or even more such reactors is used [2]. n-Hexane, n-heptane, or Ce, C7 fractions are the solvents. Catalyst, co-catalyst and other compounds are introduced with the solvent into the reactor. The monomers (ethylene, propylene) are injected as gases other olefins are introduced in liquid form. The polymerization process runs around 50 °C and at pressures up to 2 MPa. Downstream the catalyst/co-catalyst system is deactivated and their residues are dissolved in dilute acid or aqueous NaOH. The copolymer is stabilized with an antioxidant. Steam treatment removes the rest of the solvent and monomers, and agglomerates the product to crumbs. These crumbs are then dried and finished to bales or pellets. 

The time accelerated aging method for electric wires and cables requires a high dose rate irradiation, but the exposure to polymer in air results only the oxidation of surface when the dose rate is higher. I previously reported the methodology study of time accelerated irradiation of elastomer (2). The study showed two appropriate methods, one was irradiation in pressurized oxygen at room temperature the other was irradiation at 70°C in air. The article studied the effect of higher dose (up to 10 MGy) irradiation on ethylene-propylene-diene elastomer (EPDM) by using the time accelerated method. Irradiation at 70°C in air was chosen as the time accelerated irradiation condition because of the experimental convenience. 

During the last few years we have developed methods for rapid cross-linking of polyethylenes, ethylene-propylene-diene elastomers (EPDM)2 and linear unsaturated polyesters using UV light for initiation. Efficient crosslinking to high gel content has been obtained for these polymer systems, which contain small amounts of UV-absorbing initiator and a multifimctional monomer (a crosslinker),... 

Common examples of miscible blends are ethylene-propylene copolymers of different composition that result in an elastomer comprising a semicrystalline, higher ethylene content and an amorphous, lower ethylene content components. These blends combine the higher tensile strength of the semicrystaUine polymers and the favorable low temperature properties of amorphous polymers. Chemical differences in miscible blends of ethylene-propylene and styrene-butadiene copolymers can also arise from differences in the distribution and the type of vulcanization site on the elastomer. The uneven distribution of diene, which is the site for vulcanization in blends of ethylene-propylene-diene elastomers, can lead to the formation of two distinct, intermingled vulcanization networks. 

EPDM-MA Maleated ethylene-propylene-diene elastomer... 

Flow measurement is by magnetic meters with ethylene-propylene-diene elastomer (EPDM) lining and Hastelloy C electrodes. The control valve can be a rubber-lined butterfly valve with a rubber-coated or Monel disc. 

PE with ethylene-propylene-diene-elastomer, e.g. poly(ethylene-co-l,4-hexadiene-c6>-propylene) PE/EPDM... 

PP with ethylene-propylene-diene-elastomer PP/EPDM... 

Ethylene-propylene-diene elastomers Mechanical and rheological 98... 

TABLE 2.2 Composition and Basic Characteristics of Ethylene-Propylene-Diene Elastomers... 

Calculations showed that the value of -a for BNRS-28 is somewhat lower than that for BNRS-18, even though the polarity of the former rubber is higher. This phenomenon was attributed to the effect of various butadiene isomers on compatibility with ethylene-propylene-diene elastomers (Table 2.1). 

The Swiss company, WW Fischer, offers PTFE (Teflon PTFE or Hostaflon), PBT (Celanex, Crastin, Ultradur or Valox) or PEEK (Victrex) insulator material options in its 405 series of cylindrical connectors according to the requirements of working temperature and other criteria. PEEK is an expensive polymer which tends to be employed when other materials fail to meet the specification requirements of the application. Other Fischer connector types use polyamide-imide (Torlon) or POM (Celcon, Delrin or Hostaform). Elastomeric seals used by Fischer in conjunction with their connectors are made from acrylonitrile-butadiene rubber (NBR N BUNA) or to MIL-P-25732, fluoroelastomer (FPM VITON), polychloroprene elastomer (CR Neoprene), ethylene-propylene diene elastomer (EPDM) and styrene-ethylene-butadiene-styrene thermoplastic elastomer (TPE-S or TPE-O) where each compound is followed by its trade name. Fischer s Swiss competitor, Lemo, manufactures a similar range of connectors including the Redel types which have a plastic body. 

---