Ethylene, adsorption behavior

The effect of the presence of alkali promoters on ethylene adsorption on single crystal metal surfaces has been studied in the case ofPt (111).74 77 The same effect has been also studied for C6H6 and C4H8 on K-covered Pt(l 11).78,79 As ethylene and other unsaturated hydrocarbon molecules show net n- or o-donor behavior it is expected that alkalis will inhibit their adsorption on metal surfaces. The requirement of two free neighboring Pt atoms for adsorption of ethylene in the di-o state is also expected to allow for geometric (steric) hindrance of ethylene adsorption at high alkali coverages. 

Propylene oxide is a surface active monomer structurally similar to ethylene oxide and therefore of interest as a SHM W-SP, but with more than ten repeating units this polymer is not water soluble. A compositional isomer methyl vinyl ether is water soluble the adsorption behavior of this polymer (PMVE) is illustrated in Figure 4. At 1 ppm the rate of 7T increase is linear over three hours. The diffusion rate could be calculated if the W-SP s molecular weight were monodispersed. The polymer studied had a Gaussian molecular weight distribution, which is true of essentially all W-SPs even after attempts have been made to... 

Characterization of the Adsorbed Layer of a Silver Catalyst in the Oxidation of Ethylene from Its Transient Adsorption Behavior... 

In order to more deeply explore the cycloaddition process on Ge(100)-2 x 1, we will examine the case of ethylene, the smallest alkene. Rather than exhibit straightforward adsorption behavior, as might be expected for such a simple molecule,... 

It is very interesting the adsorption behavior of poly (ethylene oxide) from water solution to the air - water interface. This adsorption was considerably enhanced by a hydrophobic group placed at ends of the molecules. 

Adsorption of block copolymers onto a surface is another pathway for surface functionalization. Block copolymers in solution of selective solvent afford the possibility to both self-assemble and adsorb onto a surface. The adsorption behavior is governed mostly by the interaction between the polymers and the solvent, but also by the size and the conformation of the polymer chains and by the interfacial contact energy of the polymer chains with the substrate [115-119], Indeed, in a selective solvent, one of the blocks is in a good solvent it swells and does not adsorb to the surface while the other block, which is in a poor solvent, will adsorb strongly to the surface to minimize its contact with the solvent. There have been a considerable number of studies dedicated to the adsorption of block copolymers to flat or curved surfaces, including adsorption of poly(/cr/-butylstyrcnc)-ft/od -sodium poly(styrenesulfonate) onto silica surfaces [120], polystyrene-Woc -poly(acrylic acid) onto weak polyelectrolyte multilayer surfaces [121], polyethylene-Wocfc-poly(ethylene oxide) on alkanethiol-patterned gold surfaces [122], or poly(ethylene oxide)-Woc -poly(lactide) onto colloidal polystyrene particles [123],... 

Perhaps the best way to illustrate the diverse surface-structure chemistry of organic monolayer adsorbates is to review the adsorption behavior of ethylene and benzene on various transition metal surfaces. These two molecules are described in detail below. 

Polymers with which we will deal throughout this chapter are water soluble. They can be either ionic or nonionic. Some of them are synthetic, others are of biological origin (proteins, for instance). Both homopolymers and heteropolymers exist. Some polymers own amphiphilic monomers that induce surface-active properties to the whole polymeric structure. Water plays a very important role in determining the polymer properties in solution. The properties are also greatly modified by the addition of salts or by a pH modification. Frequently encountered nonionic polymers in polymer-surfactant interactions and their subsequent adsorption behavior at solid surfaces are poly(ethylene oxide) (PEO), poly(vinyl pyrrolidone) (PVP), polyacrylamide, and poly(vinyl alcohol). 

It is well known that pMMA and pSty in THF follow ideal GPC behavior on many common GPC columns. However, many commercially important acrylate polymers contain a wide array of other monomers. In general, acrylic polymers composed of monomers that do not contain polar groups will yield well-behaved polymers, giving ideal GPC separations. Monomers that contain polar groups should prompt the analyst to carefully evaluate the possibility of adsorption of the analyte onto the column. The most common functionalities of concern are hydroxyl groups, amine groups, ethylene oxide units, and carboxylic acids. In many cases, such monomers can be tolerated. However, the acceptable level can vary considerably with even apparently minor changes in... 

The anion vacancy sites have acid properties. As stated above, the catalytic activity and the hydrogenolytic behavior correlated with the acid properties of the catalyst, as well as the extent of reduction. Therefore, the adsorption of an aryl group will occur on the coordinatively unsaturated molybdenum sites generated during reduction. According to the reaction scheme for the hydrogenation of ethylene over a reduced MoOj-AljOj catalyst, ethylene becomes it-bonded at a second vacant ligand position of a coordinatively unsaturated Mo species and inserts to form the [Pg.267]

As alluded to before, the adsorption of atoms and molecules may also induce segregation in alloys. Upon revisiting the thermodynamic behavior of the improved Cu-Ag alloy catalysts for ethylene epoxidation synthesized by Linic et al, (section 2.1) Piccinin et al. calculated that, while in the absence of oxygen Cu prefers to stay in the subsurface layers, oxygen adsorption causes it to segregate to the surface which then phase-separates into clean Ag(lll) and various Cu surface oxides under typical industrial conditions (Fig. 7). This casts doubt on the active state of the previous Cu-Ag catalysts being a well-mixed surface Ag-Cu alloy. 

---