Ethyl acetate functional groups

In 1991, Li and Chan reported the use of indium to mediate Barbier-Grignard-type reactions in water (Eq. 8.49).108 When the allylation was mediated by indium in water, the reaction went smoothly at room temperature without any promoter, whereas the use of zinc and tin usually requires acid catalysis, heat, or sonication. The mildness of the reaction conditions makes it possible to use the indium method to allylate a methyl ketone in the presence of an acid-sensitive acetal functional group (Eq. 8.50). Furthermore, the coupling of ethyl 2-(bromomethyl)acrylate with carbonyl compounds proceeds equally well under the same reaction conditions, giving ready access to various hydroxyl acids including, for example, sialic acids. 

The combined results of kinetic studies on condensation polymerization reactions and on the degradation of various polymers by reactions which bring about chain scission demonstrate quite clearly that the chemical reactivity of a functional group does not ordinarily depend on the size of the molecule to which it is attached. Exceptions occur only when the chain is so short as to allow the specific effect of one end group on the reactivity of the other to be appreciable. Evidence from a third type of polymer reaction, namely, that in which the lateral substituents of the polymer chain undergo reaction without alteration in the degree of polymerization, also support this conclusion. The velocity of saponification of polyvinyl acetate, for example, is very nearly the same as that for ethyl acetate under the same conditions. ... 

However, when considering the use of acid or base in organic solvents for sample extraction, care must be taken to avoid potential artifacts that may arise from side reactions. For example, methylation of active hydroxyl groups or acidic functions on the analyte may sometimes occur when acidic methanol is used as the extractant. Another example is acetylation of an active alcohol on the analyte following partition of the analyte into ethyl acetate from aqueous solution acidified with glacial acetic acid. 

The comparison between the cycloaddition behavior of simple diazoketones and of ethyl diazopyruvate 56 towards the same olefin underlines the crucial influence of the ethoxycarbonyl group attached to the carbonyl function. This becomes once again evident when COOEt is replaced by an acetal function, such as in l-diazo-3,3-di-methoxy-2-butanone 86 with enol ethers and acetates, cyclopropanes rather than dihydrofurans are now obtained 113). ... 

Rh2(OAc)4 has become the catalyst of choice for insertion of carbene moieties into the N—H bond of (3-lactams. Two cases of intermolecular reaction have been reported. The carbene unit derived from alkyl aryldiazoacetates 322 seems to be inserted only into the ring N—H bond of 323 246). Similarly, N-malonyl- 3-lactams 327 are available from diazomalonic esters 325 and (3-lactams 326 297). If, however, the acetate function in 326 is replaced by an alkylthio or arylthio group, C/S insertion rather than N/H insertion takes place (see Sect. 7.2). Reaction of ethyl diazoacetoacetate 57b with 328 also yields an N/H insertion product (329) 298>, rather than ethyl l-aza-4-oxa-3-methyl-7-oxabicyclo[3.2.0]hex-2-ene-2-earboxylate, as had been claimed before 299). 

Table 7. Determination of functional groups of metabolites in ethyl acetate phase by gas-liquid... 

The product (15-2) from aldol condensation of meto-nitrobenzaldehyde with the dimethyl acetal from ethyl 4-formylacetoacetate (15-1) provides the starting material for a dihydropyridine in which one of the methyl groups is replaced by a nitrile. Reaction of (15-2) with the eneamine from isopropyl acetoacetate gives the corresponding dihydropyridine hydrolysis of the acetal function with aqueous acid affords the aldehyde (15-3). That function is then converted to its oxime (15-4) by reaction with hydroxylamine. Treatment of that intermediate with hot acetic acid leads the oxime to dehydrate to a nitrile. There is this obtained nilvadipine (15-5) [16]. 

The dibasic side chain at position 7 can be alternatively provided by a substituted amino alkyl pyrrolidine. Preparation of that diamine in chiral form starts with the extension of the ester function in pyrrolidone (46-1) by aldol condensation with ethyl acetate (46-2). Acid hydrolysis of the (3-ketoester leads to the free acid that then decarboxylates to form an acetyl group (46-3). The carbonyl group is next converted to an amine by sequential reaction with hydroxylamine to form the oxime, followed by catalytic hydrogenation. The desired isomer (46-4) is then separated... 

The functional group of an ester is an acyl group bonded to an alkoxy group (—OR). The simplest members of this family are methyl acetate (CH3COOCH3) and ethyl acetate (CH3COOCH2CH3). 

A pulse polarographic method to determine dantrolene sodium and its major metabolites in urine after ethyl acetate extraction has been reported [181]. The ethyl acetate is brought to a residue and the dantrolene plus the total extract-able metabolites are analyzed for reduction of the azomethine linkage at -0.86 V in a DMF-acetate buffer (pH 4.0). The nitro compounds are simultaneously determined in the same media as dantrolene equivalents from the reduction of the nitro group at -0.26 V (see Fig. 26.13). The difference between the two determinations represents the metabolites not containing the nitro group. Levels as low as 0.1 fig/mL can be determined for either functional group. 

---