Error ratio

Weighting scheme in LS refinement Treatment of hydrogen atoms Shift-to-error ratio, (A/(r)niax... 

Figure 14-22 In OLR, the sum of squared deviations from the line is minimized in the vertical direction. In Deming regression analysis, the sum of squared deviations is minimized at an angle to the line depending on the random error ratio. Here the symmetric case is displayed with orthogonal deviations. (From Linnet K.The performance of Deming regression analysis in case of a misspecified analytical error ratio. Clin Cbem 1998 44 1024-1031 [Figure I]).

Linnet K. The performance of Deming regression analysis in case of a misspecified analytical error ratio. Clin Chem 1998 44 1024-31. 

The video transmission tool is able to adapt to available capacities of the network by changing the video codec and/or the compression ratio before sending the data [304]. As shown in Fig. 3.45, this approach uses the Real-Time Transmission Protocol RTP for a connectionless data transmission without error handling. RTP also provides a control protocol named RTCP, by which the receiving party can give feedback information about the received data and the error ratio. The sending party uses this feedback information to... 

Radionuclide Reported value Reported error EML value EML error Ratio Evaluation Last evaluation... 

If we place a condition that the error ratio e2/ < u f vanishes with (5u, and (5 7 > all Ju p where a is some positive number, then... 

If we can find a sufficiently small neighborhood of u such that all Ju therein have norms sufficiently small to render any negative error ratio less than a/2, then... 

The ratio of products from reaction of 95a, 95b, 96a, and 96b were found to be identical within experimental error. (Ratios of 98 to 99 ranged from 1.45 to 1.55.) There was a large difference in the product distributions formed from the iodopseudocumenes, however. When the reactant was 95c, the ratio of 99 to 98 was 0.63 1.0 when the reactant was 96c, the ratio of 99 to 98 was 5.86 1.0. Furthermore, significant yields of 94 were observed from reactions with 95c and 96c. °... 

For the above reaction scheme, the error ratio, i.e. the rate of generating the incorrect product relative to the rate of generating the correct product, is simply the relative flux through the two competing Michaelis-Menten reaction channels . 

How do the resulting 0 values compare to experimental error ratios O for non-enzymatic template-directed polymerization Using chemically activated nucleotides, ref. [27] reported the measured errors incurred during non-enzymatic template-directed polymerization for all combinations of DNA and RNA templates and primers. The resulting mis-incorporation probabilities are plotted in Fig. 9.11... 

To investigate the current error (ratio error) and phase displacement for a current transformer, consider the simplified phasor diagram in Fig. 27. It can be seen that the difference in magnitude between the primary current 7p and the secondaiy current multiplied by the rated transformation ratio ihK ) is dependent on the amount of the primary current used to energize the core, which must therefore be kept to a minimum. It should be noted that a CT is operated with a load consisting of an ammeter that almost short-circuits the secondaiy terminals should this... 

NIRS equations were selected, taking into account the best values of r, SEP and other statistics ratio of performance to deviation and range error ratio. Table 1 summarizes statistics for calibration and validation of the degradability parameters. Prediction of feeds chemical composition was satisfactory. The effective degradation of DM, CP and NDF was also well predicted by the MRS equations, as well as fraction a in the case of DM and CP, and fraction b for DM. In the case of c value and the asymptote, R and r coefficients were below acceptable limits. These results are in accordance with Andres et al. (2005) and Ohlsson et al. (2007), even though current values are higher probably due to the higher variation in the present material. 

R determination coefficient of calibration, r determination coefficient of validation, SEC standard error of calibration, SEP standard error of prediction, RPD performance/deviation, RER range error ratio. 

---