Electronic chemical potential transition

Figure 7.9. Schematic representation of the density of states N(E) in the conduction band of two transition metal electrodes (W and R) and of the definitions of work function O, chemical potential of electrons p, electrochemical potential of electrons or Fermi level p, surface potential x, Galvani (or inner) potential (p and Volta (or outer) potential for the catalyst (W) and for the reference electrode (R). The measured potential difference UWr is by definition the difference in p q>, p and p are spatially uniform O and can vary locally on the metal surfaces 21 the T terms are equal, see Fig. 5.18, for the case of fast spillover, in which case they also vanish for an overall neutral cell Reprinted with permission from The Electrochemical Society.

The general way in which a Galvani potential is established is similar in all cases, but special features are observed at the metal-electrolyte interface. The transition of charged species (electrons or ions) across the interface is possible only in connection with an electrode reaction in which other species may also be involved. Therefore, equilibrium for the particles crossing the interface [Eq. (2.5)] can also be written as an equilibrium for the overall reaction involving all other reaction components. In this case the chemical potentials of aU reaction components appear in Eq. (2.6) (for further details, see Chapter 3). 

As described in the introduction, certain cosurfactants appear able to drive percolation transitions. Variations in the cosurfactant chemical potential, RT n (where is cosurfactant concentration or activity), holding other compositional features constant, provide the driving force for these percolation transitions. A water, toluene, and AOT microemulsion system using acrylamide as cosurfactant exhibited percolation type behavior for a variety of redox electron-transfer processes. The corresponding low-frequency electrical conductivity data for such a system is illustrated in Fig. 8, where the water, toluene, and AOT mole ratio (11.2 19.2 1.00) is held approximately constant, and the acrylamide concentration, is varied from 0 to 6% (w/w). At about = 1.2%, the arrow labeled in Fig. 8 indicates the onset of percolation in electrical conductivity. 

The final ingredient that enters the calculation is the density factor pw. This is the actual density of water appropriate to the thermodynamic state intended in the calculation. For the usual case of 1 atm. pressure and 298K, this is I gem 3. The reference density in the electronic structure calculations is p° = 1 atm//entropic cost of sequestering water in the metal-water complexes, the free energies should be adjusted by —mRT In (pi 2o/p ) = —mRTIn (1354). With these inputs the excess chemical potential is readily composed as per (9.50), provided the optimal value of m is known. This is found by composing the excess chemical potential for different assumed m values and identifying the most stable case. For the dication transition metals studied, this is found to be six, consistent with experiment [12]. 

However, a more realistic model for the phase transition between baryonic and quark phase inside the star is the Glendenning construction [16], which determines the range of baryon density where both phases coexist. The essential point of this procedure is that both the hadron and the quark phase are allowed to be separately charged, still preserving the total charge neutrality. This implies that neutron star matter can be treated as a two-component system, and therefore can be parametrized by two chemical potentials like electron and baryon chemical potentials [if. and iin. The pressure is the same in the two phases to ensure mechanical stability, while the chemical potentials of the different species are related to each other satisfying chemical and beta stability. The Gibbs condition for mechanical and chemical equilibrium at zero temperature between both phases reads... 

If majority point defect concentrations depend on the activities (chemical potentials) of the components, extrinsic disorder prevails. Since the components k are necessarily involved in the defect formation reactions, nonstoichiometry is the result. In crystals with electrically charged regular SE, compensating electronic defects are produced (or annihilated). As an example, consider the equilibrium between oxygen and appropriate SE s of the transition metal oxide CoO. Since all possible kinds of point defects exist in equilibrium, we may choose any convenient reaction between the component oxygen and the appropriate SE s of CoO (e.g., Eqn. (2.64))... 

Figure 1 2 1. The different types of 2.5 Lifshitz electronic topological transition (ETT) The upper panel shows the type (I) ETT where the chemical potential EF is tuned to a Van Hove singularity (vHs) at the bottom (or at the top) of a second band with the appearance (or disappearance) of a new detached Fermi surface region. The lower panel shows the type (II) ETT with the disruption (or formation) of a neck in a second Fermi surface where the chemical potential EF is tuned at a vHs associated with the gradual transformation of the second Fermi surface from a two-dimensional (2D) cylinder to a closed surface with three dimensional (3D) topology characteristics of a superlattice of metallic layers...

Thus, ionic current inside the solid electrolyte (E) and electronic current through the external electric circuit will cease after a short transition time. The chemical potential of (A) at (I) and (II) will then have the following relationship ... 

---