Elasticity temperature dependence

Table 3.2. Modulus of Elasticity— Temperature Dependence of Some Common Metals ...

To solve a flow problem or characterize a given fluid, an instmment must be carefully selected. Many commercial viscometers are available with a variety of geometries for wide viscosity ranges and shear rates (10,21,49). Rarely is it necessary to constmct an instmment. However, in choosing a commercial viscometer a number of criteria must be considered. Of great importance is the nature of the material to be tested, its viscosity, its elasticity, the temperature dependence of its viscosity, and other variables. The degree of accuracy and precision required, and whether the measurements are for quaUty control or research, must be considered. The viscometer must be matched to the materials and processes of interest otherwise, the results may be misleading. 

The design of shape-memory devices is quite different from that of conventional alloys. These materials are nonlinear, have properties that are very temperature-dependent, including an elastic modulus that not only increases with increasing temperature, but can change by a large factor over a small temperature span. This difficulty in design has been addressed as a result of the demands made in the design of compHcated smart and adaptive stmctures. Informative references on all aspects of SMAs are available (7—9). 

Thermal Properties at Low Temperatures For sohds, the Debye model developed with the aid of statistical mechanics and quantum theoiy gives a satisfactoiy representation of the specific heat with temperature. Procedures for calculating values of d, ihe Debye characteristic temperature, using either elastic constants, the compressibility, the melting point, or the temperature dependence of the expansion coefficient are outlined by Barron (Cryogenic Systems, 2d ed., Oxford University Press, 1985, pp 24-29). 

The theory relating stress, strain, time and temperature of viscoelastic materials is complex. For many practical purposes it is often better to use an ad hoc system known as the pseudo-elastic design approach. This approach uses classical elastic analysis but employs time- and temperature-dependent data obtained from creep curves and their derivatives. In outline the procedure consists of the following steps ... 

In addition to elastic turbulence (characterised by helical deformation) another phenomenon known as sharkskin may be observed. This consists of a number of ridges transverse to the extrusion direction which are often just barely discernible to the naked eye. These often appear at lower shear rates than the critical shear rate for elastic turbulence and seem more related to the linear extrudate output rate, suggesting that the phenomenon may be due to some form of slip-stick at the die exit. It appears to be temperature dependent (in a complex manner) and is worse with polymers of narrow molecular weight distribution. 

Figure 7 Intensity lines from (a) neutron (temperature dependent, courtesy Zheludev et al. ) and (b) x-ray elastic scattering experiments (stress dependent, courtesy Martynov et al. ) showing the existence of a satellite at 1/6 [110] corresponding with the modulation wavelength in the ISO s visible in figure 6.

Viscoelasticity A combination of viscous and elastic properties in a plastic with the relative contribution of each being dependent on time, temperature, stress, and strain rate. It relates to the mechanical behavior of plastics in which there is a time and temperature dependent relationship between stress and strain. A material having this property is considered to combine the features of a perfectly elastic solid and a perfect fluid. 

Temperature dependence of the elastic modulus of the plastic liner. 

The thermal conductivity plateau has traditionally been considered by most workers as a separate issue from the TLS. In addition to the rapidly growing magnitude of phonon scattering at the plateau, an excess of density of states is observed in the form of the so-called bump in the heat capacity temperature dependence divided by T. The plateau is interesting from several perspectives. For one thing, it is nonuniversal if scaled by the elastic constants (say, co/)... 

This favors a sample s contraction V is the volume). This attractive force, which will be temperature dependent, is balanced by the regular temperature-independent elastic energy of the lattice Fsiast/V = K/2) 6V/V). Calculating the equilibrium volume from this balance allows us to estimate the thermal expansion coefficient a. More specifically, the simplest Hamiltonian describing two local resonances that interact off-diagonally is... 

The recoil-free fraction depends on the oxidation state, the spin state, and the elastic bonds of the Mossbauer atom. Therefore, a temperature-dependent transition of the valence state, a spin transition, or a phase change of a particular compound or material may be easily detected as a change in the slope, a kink, or a step in the temperature dependence of In f T). However, in fits of experimental Mossbauer intensities, the values of 0 and Meff are often strongly covariant, as one may expect from a comparison of the traces shown in Fig. 2.5b. In this situation, valuable constraints can be obtained from corresponding fits of the temperature dependence of the second-order-Doppler shift of the Mossbauer spectra, which can be described by using a similar approach. The formalism is given in Sect. 4.2.3 on the temperature dependence of the isomer shift. 

Bercovici D, Lin J (1996) A gravity current model of cooling mantle plume heads with temperature dependent buoyancy and viscosity. J Geophys Res 101 3291-3309 Blundy J, Wood B (1994) Prediction of crystal-melt partition coefficients from elastic moduh. Nature 372 452-454... 

Also known for some time is a phase transition at low temperature (111K), observed in studies with various methods (NQR, elasticity measurement by ultrasound, Raman spectrometry) 112 temperature-dependent neutron diffraction showed the phase transition to be caused by an antiphase rotation of adjacent anions around the threefold axis ([111] in the cubic cell) and to lower the symmetry from cubic to rhombohedral (Ric). As shown by inelastic neutron scattering, this phase transition is driven by a low-frequency rotatory soft mode (0.288 THz 9.61 cm / 298 K) 113 a more recent NQR study revealed a small hysteresis and hence first-order character of this transition.114 This rhombohedral structure is adopted by Rb2Hg(CN)4 already at room temperature (rav(Hg—C) 218.6, rav(C—N) 114.0 pm for two independent cyano groups), and the analogous phase transition to the cubic structure occurs at 398 K.115... 

Fujima, T., Frusawa, H., Minamikawa, H., Ito, K. and Shimizu, T. (2006) Elastic precursor of the transformation from glycolipid nanotube to vesicle, Journal of Physics Condensed Matter, 18, 3089—3096. Kameta, N., Minamikawa, H., Masuda, M., Mizuno, G. and Shimizu, T. (2008) Controllable biomolecule release from self-assembled organic nanotubes with asymmetric surfaces pH and temperature dependence. Soft Matter, 4 (8), 1681-1688. Weiss R.G. and Terech P. (eds.) (2006) Molecular Gels Materials with Self-Assembled Fibrillar Networks, Springer, Dordrecht. 

The second issue of interest is the temperature dependence of elastic tunneling spectroscopy. Because the bands are intrinsically wide, spectra measure at 5 K are similar in line shape to those measured near 300 K. In any case, the integrated normalized intensities,... 

Thus, the model predicts that thermal fluctuations in the tilt and curvature change the way that the tubule radius scales with chiral elastic constant— instead of r oc (THp) 1, the scaling has an anomalous, temperature-dependent exponent. This anomalous exponent might be detectable in the scaling of tubule radius as a function of enantiomeric excess in a mixture of enantiomers or as a function of chiral fraction in a chiral-achiral mixture. 

The temperature dependences of the isothermal elastic moduli of aluminium are given in Figure 5.2 [10]. Here the dashed lines represent extrapolations for T> 7fus. Tallon and Wolfenden found that the shear modulus of A1 would vanish at T = 1.677fus and interpreted this as the upper limit for the onset of instability of metastable superheated aluminium [10]. Experimental observations of the extent of superheating typically give 1.1 Tfus as the maximum temperature where a crystalline metallic element can be retained as a metastable state [11], This is considerably lower than the instability limits predicted from the thermodynamic arguments above. 

Figure 5.2 Temperature dependence of the isothermal elastic stiffness constants of aluminium [10].

Polymers are viscoelastic materials meaning they can act as liquids, the visco portion, and as solids, the elastic portion. Descriptions of the viscoelastic properties of materials generally falls within the area called rheology. Determination of the viscoelastic behavior of materials generally occurs through stress-strain and related measurements. Whether a material behaves as a viscous or elastic material depends on temperature, the particular polymer and its prior treatment, polymer structure, and the particular measurement or conditions applied to the material. The particular property demonstrated by a material under given conditions allows polymers to act as solid or viscous liquids, as plastics, elastomers, or fibers, etc. This chapter deals with the viscoelastic properties of polymers. 

Finally, it behaves like a liquid provided the chain length is not too long. Just around T some physical properties change distinctively such as the specific volume, the expansion coefficient, the specific heat, the elastic modulus, and the dielectric constant. Determination of the temperature dependence of these quantities can thus be used to determine Tg. 

Softening as a result of micro-Brownian motion occurs in amorphous and crystalline polymers, even if they are crosslinked. However, there are characteristic differences in the temperature-dependence of mechanical properties like hardness, elastic modulus, or mechanic strength when different classes of polymers change into the molten state. In amorphous, non-crosslinked polymers, raise of temperature to values above results in a decrease of viscosity until the material starts to flow. Parallel to this softening the elastic modulus and the strength decrease (see Fig. 1.9). 

The total deformation in the four-element model consists of an instantaneous elastic deformation, delayed or retarded elastic deformation, and viscous flow. The first two deformations are recoverable upon removal of the load, and the third results in a permanent deformation in the material. Instantaneous elastic deformation is little affected by temperature as compared to retarded elastic deformation and viscous deformation, which are highly temperature-dependent. In Figure 5.62b, the total viscoelastic deformation is given by the curve OABDC. Upon unloading (dashed curve DFFG),... 

---