Dynamic mechanical analysis properties

Dynamic mechanical analysis provides a useful technique to study the cure kinetics and high temperature mechanical properties of phenoHc resins. The volatile components of the resin do not affect the scan or limit the temperature range of the experiment. However, uncured samples must be... 

Thermal analysis iavolves techniques ia which a physical property of a material is measured agaiast temperature at the same time the material is exposed to a coatroUed temperature program. A wide range of thermal analysis techniques have been developed siace the commercial development of automated thermal equipment as Hsted ia Table 1. Of these the best known and most often used for polymers are thermogravimetry (tg), differential thermal analysis (dta), differential scanning calorimetry (dsc), and dynamic mechanical analysis (dma). 

Thermal Properties. Spider dragline silk was thermally stable to about 230°C based on thermal gravimetric analysis (tga) (33). Two thermal transitions were observed by dynamic mechanical analysis (dma), one at —75° C, presumed to represent localized mobiUty in the noncrystalline regions of the silk fiber, and the other at 210°C, indicative of a partial melt or a glass transition. Data from thermal studies on B. mori silkworm cocoon silk indicate a glass-transition temperature, T, of 175°C and stability to around 250°C (37). The T for wild silkworm cocoon silks were slightly higher, from 160 to 210°C. 

Thermal and thermomechanical analyses44 are very important for determining die upper and lower usage temperature of polymeric materials as well as showing how they behave between diose temperature extremes. An especially useful thermal technique for polyurethanes is dynamic mechanical analysis (DMA).45 Uiis is used to study dynamic viscoelastic properties and measures die ability to... 

Mechanical properties. See also Dynamic mechanical analysis (DMA) of polyamides, 138 of polyester LCPs, 52 of polyurethanes, 242-244 of semicrystalline aromatic-aliphatic polyesters, 45 Mechanical recycling, 208 Medical applications, for polyurethanes, 207... 

In an NMR analysis of the effects of /-irradiation induced degradation on a specific polyurethane (PU) elastomer system, Maxwell and co-workers [87] used a combination of both H and 13C NMR techniques, and correlated these with mechanical properties derived from dynamic mechanical analysis (DMA). 1H NMR was used to determine spin-echo decay curves for three samples, which consisted of a control and two samples exposed to different levels of /-irradiation in air. These results were deconvoluted into three T2 components that represented T2 values which could be attributed to an interfacial domain between hard and soft segments of the PU, the PU soft segment, and the sol... 

An associated technique which links thermal properties with mechanical ones is dynamic mechanical analysis (DMA). In this, a bar of the sample is typically fixed into a frame by clamping at both ends. It is then oscillated by means of a ceramic shaft applied at the centre. The resonant frequency and the mechanical damping exhibited by the sample are sensitive measurements of the mechanical properties of a polymer which can be made over a wide range of temperatures. The effects of compositional changes and methods of preparation can be directly assessed. DMA is assuming a position of major importance in the study of the physico-chemical properties of polymers and composites. 

Bauer, Denneler, and Wilert-Porada also studied the influence of temperature (30-120°C) and humidity (0 - 100%) on the mechanical properties of Nation 117 membrane via dynamic mechanical analysis (DMA). The mechanical behavior of Nation membranes in a humid atmosphere was observed to differ significantly from that in dry atmosphere, and the influence of water on the mechanical properties of the acid form of Nation was found to be complex. The maximum of the storage modulus ( ) as a function of humidity was shifted to higher humidity values with increasing temperature. 

The epoxy resin formed by tetraglycidyl 4,4 -diamino diphenyl methane and 4,4 -diamino diphenyl sulfone was characterized by dynamic mechanical analysis. Epoxy specimens were exposed to varying dose levels of ionizing radiation (0.5 MeV electrons) up to 10,000 Hrads to assess their endurance in long-term space applications. Ionizing radiation has a limited effect on the mechanical properties of the epoxy. The most notable difference was a decrease of approximately 40°C in Tg after an absorbed dose of 10,000 Mrads. Sorption/desorption studies revealed that plasticization by degradation products was responsible for a portion of the decrease in Tg. 

Dynamic mechanical analysis (DMA) or dynamic mechanical thermal analysis (DMTA) provides a method for determining elastic and loss moduli of polymers as a function of temperature, frequency or time, or both [1-13]. Viscoelasticity describes the time-dependent mechanical properties of polymers, which in limiting cases can behave as either elastic solids or viscous liquids (Fig. 23.2). Knowledge of the viscoelastic behavior of polymers and its relation to molecular structure is essential in the understanding of both processing and end-use properties. 

The complex sorption behavior of the water in amine-epoxy thermosets is discussed and related to depression of the mechanical properties. The hypothesized sorption modes and the corresponding mechanisms of plasticization are discussed on the basis of experimental vapor and liquid sorption tests, differential scanning calorimetry (DSC), thermomechanical analysis (TMA) and dynamic mechanical analysis. In particular, two different types of epoxy materials have been chosen low-performance systems of diglycidyl ether of bisphenol-A (DGEBA) cured with linear amines, and high-performance formulations based on aromatic amine-cured tetraglycidyldiamino diphenylmethane (TGDDM) which are commonly used as matrices for carbon fiber composites. 

One of most popular techniques for dynamic mechanical analysis is the torsion pendulum method. In a modification of this method designed to follow curing processes, a torsion bar is manufactured from a braid of fibers impregnated with the composition to be studied this is the so-called torsional braid analysis (TBA) method.61 62,148 The forced harmonic oscillation method has been also used and has proven to be valuable. This method employs various types of rheogoniometers and vibroreometers,1 9,150 which measure the absolute values of the viscoelastic properties of the system under study these properties can be measured at any stage of the process. The use of computers further contributes to improvements in dynamic mechanical analysis methods for rheokinetic measurements. As will be seen below, new possibilities are opened up by applying computer methods to results of dynamic measurements. 

The physical properties of barrier dressings were evaluated using the Seiko Model DMS 210 Dynamic Mechanical Analyzer Instrument (see Fig. 2.45). Referring to Fig. 2.46, dynamic mechanical analysis consists of oscillating (1 Hz) tensile force of a material in an environmentally (37°C) controlled chamber (see Fig. 2.47) to measure loss modulus (E") and stored modulus (E ). Many materials including polymers and tissue are viscoelastic, meaning that they deform (stretch or pull) with applied force and return to their original shape with time. The effect is a function of the viscous property (E") within the material that resists deformation and the elastic property (E )... 

---