Linear driving

An electric-drive linear-traversing sampler of minimum standard manufactured size with cutter ana controls will range upwards of 8,000. 

One-structure interpolation methods coordinate driving, linear and quadratic synchronous transit, and sphere optimization... 

Introduction of linear motors for driving linear slides... 

In Section 5.2.8 we shall look at pressure-depth relationships, and will see that the relationship is a linear function of the density of the fluid. Since water is the one fluid which is always associated with a petroleum reservoir, an understanding of what controls formation water density is required. Additionally, reservoir engineers need to know the fluid properties of the formation water to predict its expansion and movement, which can contribute significantly to the drive mechanism in a reservoir, especially if the volume of water surrounding the hydrocarbon accumulation is large. 

The primary drive mechanism for gas field production is the expansion of the gas contained in the reservoir. Relative to oil reservoirs, the material balance calculations for gas reservoirs is rather simple the recovery factor is linked to the drop in reservoir pressure in an almost linear manner. The non-linearity is due to the changing z-factor (introduced in Section 5.2.4) as the pressure drops. A plot of (P/ z) against the recovery factor is linear if aquifer influx and pore compaction are negligible. The material balance may therefore be represented by the following plot (often called the P over z plot). 

Figure Bl.5.2 Nonlinear dependence of tire polarization P on the electric field E. (a) For small sinusoidal input fields, P depends linearly on hence its hannonic content is mainly tiiat of E. (b) For a stronger driving electric field E, the polarization wavefomi becomes distorted, giving rise to new hannonic components. The second-hamionic and DC components are shown.

If the polarization of a given point in space and time (r, t) depends only on the driving electric field at the same coordmates, we may write tire polarization as P = P(E). In this case, we may develop the polarization m power series as P = = P - + P - + P - +, where the linear temi is = X] Jf/ Pyand the... 

Log arithmic-Mean Driving Force. As noted eadier, linear operating lines occur if all concentrations involved stay low. Where it is possible to assume that the equiUbrium line is linear, it can be shown that use of the logarithmic mean of the terminal driving forces is theoretically correct. When the overall gas-film coefficient is used to express the rate of absorption, the calculation reduces to solution of the equation... 

Fig. 9. Uptake curves for N2 in two samples of carbon molecular sieve showing conformity with diffusion model (eq. 24) for sample 1 (A), and with surface resistance model (eq. 26) for example 2 (0)j LDF = linear driving force. Data from ref. 18.

This rate equation must satisfy the boundary conditions imposed by the equiUbrium isotherm and it must be thermodynamically consistent so that the mass transfer rate falls to 2ero at equiUbrium. It maybe a linear driving force expression of the form... 

Fig. 15. Theoretical breakthrough curves for a nonlinear (Langmuir) system showing the comparison between the linear driving force (—), pore diffusion (--------------------), and intracrystalline diffusion (-) models based on the Glueckauf approximation (eqs. 40—45). From Ref. 7.

This reaction also plays a role in the degradation of polysulftdes. A back-biting mechanism as shown in equation 6 results in formation of the cycHc disulfide (5). Steam distillation of polysulftdes results in continuous gradual collection of (5). There is an equiUbrium between the linear polysulftde polymer and the cycHc disulfide. Although the linear polymer is favored and only small amounts of the cycHc compound are normally present, conditions such as steam distillation, which remove (5), drive the equiUbrium process toward depolymerization. 

Linear Driving Force Approximation Simplified expressions can also be used for an approximate description of adsorption in terms of rate coefficients for both extrapai ticle and intraparticle mass transfer controlling. As an approximation, the rate of adsorption on a particle can be written as ... 

The linear driving force (LDF) approximation is obtained when the driving force is expressed as a concentration difference. It was originally developed to describe packed-bed dynamics under linear eqm-librium conditions [Glueckauf, Trans. Far Soc., 51, 1540 (1955)]. This form is exact for a nonlinear isotherm only when external mass transfer is controlling. However, it can also be used for nonlinear sys-... 

Overall Resistance With a linear isotherm (R = 1), the overall mass transfer resistance is the sum of intraparticle and extraparticle resistances. Thus, the overall LDF coefficient for use with a particle-side driving force (column 2 in Table 16-12) is ... 

Axial Dispersion Effects In adsorption bed calculations, axial dispersion effects are typically accounted for by the axial diffusionhke term in the bed conservation equations [Eqs. (16-51) and (16-52)]. For nearly linear isotherms (0.5 < R < 1.5), the combined effects of axial dispersion and mass-transfer resistances on the adsorption behavior of packed beds can be expressed approximately in terms of an apparent rate coefficient for use with a fluid-phase driving force (column 1, Table 16-12) ... 

Figure 16-27 compares the various constant pattern solutions for R = 0.5. The curves are of a similar shape. The solution for reaction kinetics is perfectly symmetrical. The cui ves for the axial dispersion fluid-phase concentration profile and the linear driving force approximation are identical except that the latter occurs one transfer unit further down the bed. The cui ve for external mass transfer is exactly that for the linear driving force approximation turned upside down [i.e., rotated 180° about cf= nf = 0.5, N — Ti) = 0]. The hnear driving force approximation provides a good approximation for both pore diffusion and surface diffusion. 

FIG. 16-27 Constant pattern solutions for R = 0.5. Ordinant is cfor nfexcept for axial dispersion for which individual curves are labeled a, axial dispersion h, external mass transfer c, pore diffusion (spherical particles) d, surface diffusion (spherical particles) e, linear driving force approximation f, reaction kinetics. [from LeVan in Rodrigues et al. (eds.), Adsorption Science and Technology, Kluwer Academic Publishers, Dor drecht, The Nether lands, 1989 r eprinted with permission.]... 

The rectangular isotherm has received special attention. For this, many of the constant patterns are developed fuUy at the bed inlet, as shown for external mass transfer [Klotz, Chem. Rev.s., 39, 241 (1946)], pore diffusion [Vermeulen, Adv. Chem. Eng., 2, 147 (1958) Hall et al., Jnd. Eng. Chem. Fundam., 5, 212 (1966)], the linear driving force approximation [Cooper, Jnd. Eng. Chem. Fundam., 4, 308 (1965)], reaction kinetics [Hiester and Vermeulen, Chem. Eng. Progre.s.s, 48, 505 (1952) Bohart and Adams, J. Amei Chem. Soc., 42, 523 (1920)], and axial dispersion [Coppola and LeVan, Chem. Eng. ScL, 38, 991 (1983)]. 

The simplest isotherm is /if = cf corresponding to R = 1. For this isotherm, the rate equation for external mass transfer, the linear driving force approximation, or reaction kinetics, can be combined with Eq. (16-130) to obtain... 

---