Diameters, 146 Electron multipliers

Soft X-ray absorption measurements are done at low-energy synchrotron X-ray facilities such as the UV ring at NSLS or the Advanced Photon Source (APS) at Lawrence Berkeley National Laboratory (LBNL). The beam size is typically 1 mm in diameter. The electron yield data are usually obtained in the total electron yield (EY) mode, measuring the current from a channel electron multiplier (Channeltron). Sometimes a voltage bias is applied to increase surface sensitivity. This is referred to as the partial electron yield (PEY) mode. Huorescence yield (EY) data are recorded using a windowless energy dispersive Si (Li) detector. The experiments are conducted in vacuum at a pressure of 2 X 10 torr. 

Fig. 10.2 Major components of a thermal atomic beam apparatus for microwave ionization experiments,the atomic source, the microwave cavity, and the electron multiplier. The microwave cavity is shown sliced in half. The Cu septum bisects the height of the cavity. Two holes of diameter 1.3 mm are drilled in the side walls to admit the collinear laser and Na atomic beams, and a 1 mm hole in the top of the cavity allows Na+ resulting from a field ionization of Na to be extracted. Note the slots for pumping (from ref. 4).

The atomic beam was formed by a multichannel capillary array, placed perpendicular to the positron beam, with a 2.5 mm2 effusing area and a length-to-diameter ratio of 25 1. The head pressure behind the array was kept at 9 torr (ss 103 Pa) in the initial measurements. An annealed tungsten moderator was used to provide a beam of more than 105 positrons per second at 200 eV. A much more intense beam of electrons could also be obtained by reversing the electrostatic potentials on the various elements which made up the transport system. Channel electron multipliers (CEM1 and CEM2 respectively) were used to monitor the incident and scattered beams. In later versions of the apparatus, a third... 

Figure 4. Micro channel electron multiplier plate. Round approach 14 pm diameter, 17 pm center-to-center. Square Approach 16.3 pm square, 20 pm cen-...

Another type of continuous dynode electron multipliers is the microchannel plate (MCP) detector. It is a plate in which parallel cylindrical channels have been drilled. The channel diameter ranges from 4 to 25 pm with a centre-to-centre distance ranging from 6 to 32 pm and a few millimetres in length (Figure 3.4). The plate input side is kept at a negative potential of about 1 kV compared with the output side. 

A newer and less expensive alternative to the microchannel plate is the microsphere plate (MSP). As illustrated in Figure 3.6, this electron multiplier consists of glass beads with diameters from 20 to 100 pm that are sintered to form a thin plate with a thickness of 0.7 mm. This plate is porous with irregularly shaped channels between the planar faces. The surfaces of the beads are covered with an electron emissive material and the two sides of the plate are coated to make them conductive. The operating principle of this electron multiplier is similar to that of the microchannel plate. A potential difference of between 1.5 and 3.5 kV is applied across the plate, with the output side of the plate at the more positive potential. When particles hit the input side of the microsphere plate, they produce secondary electrons. These electrons are then accelerated by the electric field through the porous plate and collide with other beads. Secondary electron multiplication in the gaps occurs and finally a large number of secondary electrons are emitted from the output side of the plate. 

An MCP is a glass disk perforated with a large number of small-diameter (10-100 )Lim) holes or channels. Each channel is a glass tube coated with a resistive secondary electron-emitting material. If a voltage is applied, each channel acts as an electron multiplier. 

The microchannel plate is a spatially resolved array detector formed of 10 -10 continuous-dynode electron multipliers, each only 10-100 ptm in diameter. This detector is used in focal plane mass spectrometers as a replacement for photograph plate detectors and is used in some TOFMS instruments. 

Figure 7.9 (a) Sketch of a cutaway view of a channel electron multiplier array plate. Nickel-chromium electroding is applied to both surfaces of a microchannel plate to provide electrical contact and also penetrates into the channel. The penetration depth is minimized on the input face (0.3-0.7 of the channel diameter) to maximize the first strike conversion efficiency of incoming ions/elecrons channel. Reproduced from Wiza, Nucl. Instrum. Methods 162,587 (1979), copyright (1979), with permission from Elsevier. 

---