Cyclohexanone surface reaction

Figure 22.1.16. Surface reaction of cyclohexanone on activated carbon (After reference 25).

Acetylcyclohexanone. Method A. Place a mixture of 24-6 g. of cyclohexanone (regenerated from the bisulphite compound) and 61 g. (47 5 ml.) of A.R. acetic anhydride in a 500 ml. three-necked flask, fitted with an efficient sealed stirrer, a gas inlet tube reaching to within 1-2 cm. of the surface of the liquid combined with a thermometer immersed in the liquid (compare Fig. II, 7, 12, 6), and (in the third neck) a gas outlet tube leading to an alkali or water trap (Fig. II, 8, 1). Immerse the flask in a bath of Dry Ice - acetone, stir the mixture vigorously and pass commercial boron trifluoride (via an empty wash bottle and then through 95 per cent, sulphuric acid) as fast as possible (10-20 minutes) until the mixture, kept at 0-10°, is saturated (copious evolution of white fumes when the outlet tube is disconnected from the trap). Replace the Dry Ice-acetone bath by an ice bath and pass the gas in at a slower rate to ensure maximum absorption. Stir for 3 6 hours whilst allowing the ice bath to attain room temperature slowly. Pour the reaction mixture into a solution of 136 g. of hydrated sodium acetate in 250 ml. of water, reflux for 60 minutes (or until the boron fluoride complexes are hydrolysed), cool in ice and extract with three 50 ml. portions of petroleum ether, b.p. 40-60° (1), wash the combined extracts free of acid with sodium bicarbonate solution, dry over anhydrous calcium sulphate, remove the solvent by... 

Several approaches have been undertaken to construct redox active polymermodified electrodes containing such rhodium complexes as mediators. Beley [70] and Cosnier [71] used the electropolymerization of pyrrole-linked rhodium complexes for their fixation at the electrode surface. An effective system for the formation of 1,4-NADH from NAD+ applied a poly-Rh(terpy-py)2 + (terpy = terpyridine py = pyrrole) modified reticulated vitreous carbon electrode [70]. In the presence of liver alcohol dehydrogenase as production enzyme, cyclohexanone was transformed to cyclohexanol with a turnover number of 113 in 31 h. However, the current efficiency was rather small. The films which are obtained by electropolymerization of the pyrrole-linked rhodium complexes do not swell. Therefore, the reaction between the substrate, for example NAD+, and the reduced redox catalyst mostly takes place at the film/solution interface. To obtain a water-swellable film, which allows the easy penetration of the substrate into the film and thus renders the reaction layer larger, we used a different approach. Water-soluble copolymers of substituted vinylbipyridine rhodium complexes with N-vinylpyrrolidone, like 11 and 12, were synthesized chemically and then fixed to the surface of a graphite electrode by /-irradiation. The polymer films obtained swell very well in aqueous... 

Another example is unpleasant odor from wall, ceiling, and floor coverings made of composite cork. Emissions of phenol and furfural were found to be high, particularly those from cork parquet. The ranges of emission factors were found to be similar for some solvents such as cyclohexanone or toluene, which are constituents of varnishes used to protect cork surfaces. The emission of furfural may result from chemical reactions in the cork during the production process or may be caused by additives such as binders (Horn et al., 1998). 

Rather high (80-90%) yields of dihydrodiazepines are observed when the reaction is carried out on a MgO surface in the presence of phosphorus chlor-oxide [17]. In this manner some dihydrobezodiazepine derivatives 78 and 80 with alkyl substituents are obtained (Scheme 4.25). It should be noted that high product yields are also observed in the reactions of o-PDA with cyclic ketones (e.g., cyclopentanone, cyclohexanone and cycloheptanone), which is not typical of routine acid catalysis [14, 99]. 

Microwave-assisted organic synthesis may also be used for carrying out the multicomponent reactions of ketones and 1,2-diamines [20, 21, 92, 100]. For example, the three-component reaction of o-PDA 1 with acetoacetic acid ethyl ester 83 and a series of aromatic and heteroaromatic aldehydes 84 proceeds under microwave irradiation with very high yields of diazepines 85 (up to 95%) [100]. Reaction of 2 equiv of cyclohexanone 86 with o-PDA 1 was also realized in a microwave field on a basic alumina surface in 4 min [92] (Scheme 4.27). 

The amount of cyclohexanone desorbed from the catalyst surface during hydrogenation can be conveniently obtained by applying the equation derived on the basis of the reaction pathways shown in Scheme 11.7, where CA and CB are the concentrations of phenol and cyclohexanone, respectively, when the initial concentration of phenol is taken as unity,/is the fraction of cyclohexanone desorbed from the catalyst... 

A simple oxide catalyst can be used in either the bulk state or supported on an inert oxide support material. The bulk oxides are usually prepared using a precipitation-calcination sequence similar to those described in Chapter 9 for the preparation of support oxides. " In general, the simple semiconductor oxides are not very good catalysts for synthetic reactions. The insulator oxides, however, can be used as solid acids and bases for a number of reactions. Alumina has been used as an acid catalyst for the vapor phase rearrangement of cyclohexanone oxime to caprolactam (Eqn. 10.9). Modification of the y-alumina surface by the addition of 10-20% of B2O3 increased its activity for this reaction, giving caprolactam in 80% selectivity even after several hours of continuous operation. "... 

---