Curing glass transition temperature

Figure 6. AT-Resin Initial and Cured Glass Transition Temperatures (Tgs).

The more common techniques used to analyze thermosets and composites are thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC), which can determine the thermal properties and also the best conditions for application of the materials. These techniques can be apphed to polymers to determine their specific heat, degree of polymerization, flanunability, degradation, cure, glass transition temperature (Tg), and other characteristics. Analysis of composites should consider the behavior of each component, including the matrix, reinforcement, plasticizers and fire retardants. 

Higher as-moulded and post-cured glass transition temperatures. 

Nanoconfinement, dicyanate ester/polycyanurate, curing, glass transition temperature, controlled pore glass... 

Elastomeric Modified Adhesives. The major characteristic of the resins discussed above is that after cure, or after polymerization, they are extremely brittie. Thus, the utility of unmodified common resins as stmctural adhesives would be very limited. Eor highly cross-linked resin systems to be usehil stmctural adhesives, they have to be modified to ensure fracture resistance. Modification can be effected by the addition of an elastomer which is soluble within the cross-linked resin. Modification of a cross-linked resin in this fashion generally decreases the glass-transition temperature but increases the resin dexibiUty, and thus increases the fracture resistance of the cured adhesive. Recendy, stmctural adhesives have been modified by elastomers which are soluble within the uncured stmctural adhesive, but then phase separate during the cure to form a two-phase system. The matrix properties are mosdy retained the glass-transition temperature is only moderately affected by the presence of the elastomer, yet the fracture resistance is substantially improved. 

Plasticizers and Processing Aids. Petroleum-based oils are commonly used as plasticizers. Compound viscosity is reduced, and mixing, processing, and low temperature properties are improved. Air permeabihty is increased by adding extender oils. Plasticizers are selected for their compatibihty and low temperature properties. Butyl mbber has a solubihty parameter of ca 15.3 (f /cm ) [7.5 (cal/cm ) ], similar to paraffinic and naphthenic oils. Polybutenes, paraffin waxes, and low mol wt polyethylene can also be used as plasticizers (qv). Alkyl adipates and sebacates reduce the glass-transition temperature and improve low temperature properties. Process aids, eg, mineral mbber and Stmktol 40 ms, improve filler dispersion and cured adhesion to high unsaturated mbber substrates. 

This combination of monomers is unique in that the two are very different chemically, and in thek character in a polymer. Polybutadiene homopolymer has a low glass-transition temperature, remaining mbbery as low as —85° C, and is a very nonpolar substance with Htde resistance to hydrocarbon fluids such as oil or gasoline. Polyacrylonitrile, on the other hand, has a glass temperature of about 110°C, and is very polar and resistant to hydrocarbon fluids (see Acrylonitrile polymers). As a result, copolymerization of the two monomers at different ratios provides a wide choice of combinations of properties. In addition to providing the mbbery nature to the copolymer, butadiene also provides residual unsaturation, both in the main chain in the case of 1,4, or in a side chain in the case of 1,2 polymerization. This residual unsaturation is useful as a cure site for vulcanization by sulfur or by peroxides, but is also a weak point for chemical attack, such as oxidation, especially at elevated temperatures. As a result, all commercial NBR products contain small amounts ( 0.5-2.5%) of antioxidant to protect the polymer during its manufacture, storage, and use. 

The two-component urethane structural adhesives are among the most difficult to characterize, simply because of the widely varying properties that are possible. These adhesives may be rigid plastics similar in modulus to standard epoxy adhesives, with glass transition temperatures of the cured adhesive being approximately 60°C. 

While phenol is the most common monomer for novolac manufacture, it is far more common to see incorporation of other phenolic materials with novolacs than with resoles. Cresols, xylenols, resorcinol, catechols, bisphenols, and a variety of phenols with longer alkyl side chains are often used. While most resoles are made with a single phenolic monomer, two or more phenolic materials are often seen in novolac formulae. These additional monomers may be needed to impart special flow characteristics under heat, change a glass transition temperature, modify cure speed, or to adjust solubility in the application process among others. 

Strict control of the fusion process is imperative. In addition to thickness, hardness, continuity and adhesion checks, correct cure may be assessed by differential scanning calorimetry techniques, which are designed to measure any difference in the glass transition temperature of a laboratory-cured powder and the cured coating taken from the factory-coated pipe. 

The simple relation (6.1) is quite useful. It allows an estimate of the gain or loss in yield strength if the glass transition temperature is changed, as for instance by the progress of the curing reaction, by radiation damage, or by absorption of water and of solvents. The ATe is determined fairly easily by thermoanalytical measurements. 

Network properties and microscopic structures of various epoxy resins cross-linked by phenolic novolacs were investigated by Suzuki et al.97 Positron annihilation spectroscopy (PAS) was utilized to characterize intermolecular spacing of networks and the results were compared to bulk polymer properties. The lifetimes (t3) and intensities (/3) of the active species (positronium ions) correspond to volume and number of holes which constitute the free volume in the network. Networks cured with flexible epoxies had more holes throughout the temperature range, and the space increased with temperature increases. Glass transition temperatures and thermal expansion coefficients (a) were calculated from plots of t3 versus temperature. The Tgs and thermal expansion coefficients obtained from PAS were lower titan those obtained from thermomechanical analysis. These differences were attributed to micro-Brownian motions determined by PAS versus macroscopic polymer properties determined by thermomechanical analysis. 

Preparation and thermal crosslinking reactions of oc, -vinylbenzyl terminated polysulfone-b-polydimethylsiloxane, ABA type block copolymers have been discussed 282,313) However, relatively little characterization was reported. Molecular weights of polysulfone and PDMS segments in the copolymers were varied between 800-8,000 and 500-11,000 g/mole, respectively. After thermal curing, the networks obtained showed two phase morphologies as indicated by the detection of two glass transition temperatures (—123 °C and +200 °C) corresponding to PDMS and polysulfone phases, respectively. No mechanical characterization data were provided. 

---