Crystal surface region

When such features exist, they are penetrated by the electron beam so the material is represented by a three-dimensional point lattice and diffraction only occurs when the Ewald sphere intersects a point. This produces a transmission-type spot pattern. For smooth surfaces, the diffraction pattern appears as a set of streaks normal to the shadow edge on the fluorescent screen, due to the interaction of the Ewald sphere with the rods projecting orthogonally to the plane of the two-dimensional reciprocal lattice of the surface. The reciprocal lattice points are drawn out into rods because of the very small beam penetration into the crystal (2—5 atomic layers). We would emphasize, however, that despite contrary statements in the literature, the appearance of a streaked pattern is a necessary but not sufficient condition by which to define an atomically flat surface. Several other factors, such as the size of the crystal surface region over which the primary wave field is coherent and thermal diffuse scattering effects (electron—phonon interactions) can influence the intensity modulation along the streaks. 

Molecular dynamics calculations have been made on atomic crystals using a Lennard-Jones potential. These have to be done near the melting point in order for the iterations not to be too lengthy and have yielded density functioi). as one passes through the solid-vapor interface (see Ref. 45). The calculations showed considerable mobility in the surface region, amounting to the presence of a... 

Surface states can be divided into those that are intrinsic to a well ordered crystal surface with two-dimensional periodicity, and those that are extrinsic [25]. Intrinsic states include those that are associated with relaxation and reconstruction. Note, however, that even in a bulk-tenuinated surface, the outemiost atoms are in a different electronic enviromuent than the substrate atoms, which can also lead to intrinsic surface states. Extrinsic surface states are associated with imperfections in the perfect order of the surface region. Extrinsic states can also be fomied by an adsorbate, as discussed below. 

Electrons interact with solid surfaces by elastic and inelastic scattering, and these interactions are employed in electron spectroscopy. For example, electrons that elastically scatter will diffract from a single-crystal lattice. The diffraction pattern can be used as a means of stnictural detenuination, as in FEED. Electrons scatter inelastically by inducing electronic and vibrational excitations in the surface region. These losses fonu the basis of electron energy loss spectroscopy (EELS). An incident electron can also knock out an iimer-shell, or core, electron from an atom in the solid that will, in turn, initiate an Auger process. Electrons can also be used to induce stimulated desorption, as described in section Al.7.5.6. 

A large number of ordered surface structures can be produced experimentally on single-crystal surfaces, especially with adsorbates [H]. There are also many disordered surfaces. Ordering is driven by the interactions between atoms, ions or molecules in the surface region. These forces can be of various types covalent, ionic, van der Waals, etc and there can be a mix of such types of interaction, not only within a given bond, but also from bond to bond in the same surface. A surface could, for instance, consist of a bulk material with one type of internal bonding (say, ionic). It may be covered with an overlayer of molecules with a different type of intramolecular bonding (typically covalent) and the molecules may be held to the substrate by yet another fomi of bond (e.g., van der Waals). 

Stony Irons. The stony iron meteorites are composed of substantial iron and siUcate components. The paHasites contain cm-sized ohvine crystals embedded ia a soHd FeNi metal matrix and have properties consistent with formation at the core mantle boundary of differentiated asteroids. The mesosiderites are composed of metal and siUcates that were fractured and remixed, presumably ia the near-surface regions of their parent bodies. 

Because the time at high temperature is much less, austenite is produced, which is chemically inhomogeneous especially with undissolved carbides, and has a fine grain crystal size. The formation of the hard martensite requites more rapid cooling than for conventional hardening. Thus case hardening by heat treatment intrinsically requites that the surface region to be hardened be relatively thin and cooled rapidly. 

The Ti02 (001) surface was cleaned and reduced by cycles of ion bombardment as previously described [3]. The distribution of titanium oxidation states was determined from cxirve fitting the Ti(2p3/2) envelope in x-ray photoelectron spectra [3]. After surface preparation, reaction experiments were conducted in either the TPD or steady state mode. TPD experiments have been described [1]. XPS spectra were also obtained following a saturation exposure of the sample using the same procedure as that for the TPD experiments. After pump down, the crystal was placed under the Mg X-ray source and the Ti(2p), 0(ls), and C(ls) regions were scanned. For steady-state experiments a dosing needle was aligned perpendicular to the axis of the mass spectrometer. It was used to direct a steady beam of methylacetylene (Linde, 95%) at the crystal surface when the sample was placed at the aperture of the mass spectrometer. Steady state reaction experiments were... 

An increased selectivity for phenol in the oxidation of benzene by H202 with TS-1 catalyst in sulfolane solvent was attributed to the formation of a bulky sulfolane-phenol adduct which cannot enter the pores of TS-1. Further oxidation of phenol to give quinones, tar, etc. is thus avoided. Removal of Ti ions from the surface regions of TS-1 crystals by treatment with NH4HF2 and H202 was also found to improve the activity and selectivity (227). The beneficial effects of removal of surface Al ions on the catalytic performance of zeolite catalysts for acid-catalyzed reactions have been known for a long time. 

Conventional HRTEM operates at ambient temperature in high vacuum and directly images the local structure of a catalyst at the atomic level, in real space. In HRTEM, as-prepared catalyst powders can be used without additional sample preparation. The method does not normally require special treatment of thin catalyst samples. In HRTEM, very thin samples can be treated as WPOs, whereby the image intensity can be correlated with the projected electrostatic potential of the crystal, leading to the atomic structural information characterizing the sample. Furthermore, the detection of electron-stimulated XRE in the EM permits simultaneous determination of the chemical composition of the catalyst. Both the surface and sub-surface regions of catalysts can be investigated. 

Inert Gases. The calculation of 7 should be relatively straightforward for crystals of inert gases, in which only one kind of interaction may be expected. These crystals have a face-centered cubic structure. If each atom is treated as a point source of attractive and repulsive forces, only the forces between the nearest pairs of atoms are considered, the zero point energy is neglected, and no re-arrangement of atoms in the surface region is permitted, then the calculated 7 still depends on the equation selected to represent the interatomic potential U. 

---