Cooling Fabric

Sweat management has been a key requirement for sportswear for some time. It is generally accepted that excessive sweat deposited onto the skin leads to discomfort and potentially other performance issues. Textile technologies to manage sweat have been in place for a number of years and include wicking yams and fabrics that carry sweat away from the skin and cooling fabrics that help reduce excessive heat on the skin. 

Texturing. The final step in olefin fiber production is texturing the method depends primarily on the appHcation. For carpet and upholstery, the fiber is usually bulked, a procedure in which fiber is deformed by hot air or steam jet turbulence in a no22le and deposited on a moving screen to cool. The fiber takes on a three-dimensional crimp that aids in developing bulk and coverage in the final fabric. Stuffer box crimping, a process in which heated tow is overfed into a restricted oudet box, imparts a two-dimensional sawtooth crimp commonly found in olefin staple used in carded nonwovens and upholstery yams. 

Antimony Oxide as a Primary Flame Retardant. Antimony oxide behaves as a condensed-phase flame retardant in cellulosic materials (2). It can be appHed by impregnating a fabric with a soluble antimony salt followed by a second treatment that precipitates antimony oxide in the fibers. When the treated fabric is exposed to a flame, the oxide reacts with the hydroxyl groups of the cellulose (qv) causing them to decompose endothermically. The decomposition products, water and char, cool the flame reactions while slowing the production and volatilization of flammable decomposition products (see Flaa retardants for textiles). 

Modified ETEE is less dense, tougher, and stiffer and exhibits a higher tensile strength and creep resistance than PTEE, PEA, or EEP resins. It is ductile, and displays in various compositions the characteristic of a nonlinear stress—strain relationship. Typical physical properties of Tef2el products are shown in Table 1 (24,25). Properties such as elongation and flex life depend on crystallinity, which is affected by the rate of crysta11i2ation values depend on fabrication conditions and melt cooling rates. 

HoUow-fiber fabrication methods can be divided into two classes (61). The most common is solution spinning, in which a 20—30% polymer solution is extmded and precipitated into a bath of a nonsolvent, generally water. Solution spinning allows fibers with the asymmetric Loeb-Soufirajan stmcture to be made. An alternative technique is melt spinning, in which a hot polymer melt is extmded from an appropriate die and is then cooled and sohdified in air or a quench tank. Melt-spun fibers are usually relatively dense and have lower fluxes than solution-spun fibers, but because the fiber can be stretched after it leaves the die, very fine fibers can be made. Melt spinning can also be used with polymers such as poly(trimethylpentene), which are not soluble in convenient solvents and are difficult to form by wet spinning. 

P/M Tool Steels. In conventionally produced high alloy tool steels (slowly cooled cast ingots), carbide tends to segregate (48). Segregated clusters of carbide persist even after hot working, and cause undesirable effects on tool fabrication and tool performance. P/M tool steels, on the other hand, provide very fine and uniform carbides in the compact, the final bar stock, and the tools. Several tool steel suppHers consoHdate gas-atomized tool steel powder by HIP to intermediate shapes, which are then hot-worked to final mill shapes. Water-atomized tool steel powder is also available (see also T OOL materials). ... 

Fig. 4. Diffusion bonding process (a) apply metal foil and cut to shape, (b) lay up desired pHes, (c) vacuum encapsulate and heat to fabrication temperature, (d) apply pressure and hold for consoHdation cycle, and (e) cool, remove, and clean part.

Powder and sponge may be compacted at 0.7 GPa (6900 atm) into bars which are presintered at 1400—1500°C in vacuum. The bars then are resistance-heated in high vacuum to slightly below the melting point. After cooling, the bars are roUed to consoHdate the pores and are resintered at 2300°C to yield a fabricable metal product of 98% theoretical density. 

---