Comminution methods

The result of taking into account the three factors mentioned - dose - degree of comminution - method of extraction - should be a tea that has an optimal amount of active constituents. But, at present ihere are very few studies which answer the often posed question What proportion of the active principles in the drug pass over into the tea With a hot-watcr infusion of chopped senna... 

Boles, J.A., and Shand, P.J. (1998). Effects of comminution method and raw binder system in restructured beef Meat Science 49, 297-307. 

An emulsion has been defined above as a thermodynamically unstable heterogeneous system of two immiscible liquids where one is dispersed in the other. There are two principal possibilities for preparing emulsions the destruction of a larger volume into smaller sub-units (comminution method) or the construction of emulsion droplets from smaller units (condensation method). Both methods are of technical importance for the preparation of emulsions for polymerization processes and will be discussed in more detail below. To impart a certain degree of kinetic stability to emulsions, different additives are employed which have to fulfil special demands in the particular applications. The most important class of such additives, which are also called emulsifying agents, are surface-active and hence influence the interfacial properties. In particular, they have to counteract the rapid coalescence of the droplets caused by the van der Waals attraction forces. In the polymerization sense, these additives can be roughly subdivided into surfactants for emulsion polymerization, polymers for suspension and dispersion polymerization, finely dispersed insoluble particles (also for suspension polymerization), and combinations thereof (cf. below). 

In atomization, a stream of molten metal is stmck with air or water jets. The particles formed are collected, sieved, and aimealed. This is the most common commercial method in use for all powders. Reduction of iron oxides or other compounds in soHd or gaseous media gives sponge iron or hydrogen-reduced mill scale. Decomposition of Hquid or gaseous metal carbonyls (qv) (iron or nickel) yields a fine powder (see Nickel and nickel alloys). Electrolytic deposition from molten salts or solutions either gives powder direcdy, or an adherent mass that has to be mechanically comminuted. 

Size reduction (qv) or comminution is the first and very important step in the processing of most minerals (2,6,10,20—24). It also involves large expenditures for heavy equipment, energy, operation, and maintenance. Size reduction is necessary because the value minerals are intimately associated with gangue and need to be Hberated, and/or because most minerals processing/separation methods require the ore mass to be of certain size and/or shape. Size reduction is also required in the case of quarry products to produce material of controlled particle size (see Size measurement of particles). In some instances, hberation of valuables or impurities from the ore matrix is achieved without any apparent size reduction. Scmbbers and attritors used in the industrial minerals plants, eg, phosphate, mtile, glass sands, or clay, ate examples. 

Extent of comminution of the drug Method of extraction (temperature, length of time)... 

Infusion Boiling water (150 250 ml) is poured over the prescribed amount of drug in a heat-resistant glass or porcelain vessel, which is then covered if necessary, the contents are stirred occasionally. If no other indication is given, the contents arc strained after 5 -10 min. This method can be used for most leaves, flowers, and herbs and also for many correspondingly comminuted barks and roots. 

The mechanisms of comminution are complex involving breakage along particle cracks and fissures etc., and depend on the hardness and structure of the feed particle. The Institution of Chemical Engineers (London) produced a major report on comminution (IChem, 1975), which was followed by reviews by Bemrose and Bridgwater (1987), Prior etal. (1990) and Jones (1997). These reviews included sections on both the fundamental and practical aspects of comminution and attrition in process equipment, test methods and an extensive list of references. 

From animal tissue, especially bovine lung and liver (e. g. autolysis of comminuted tissue parts, heating with ammonium sulfate in alkaline solution, filtration and acidification yield heparin as complex with protein, removal of fat with alcohol and treatment with trypsine for the purpose of decomposition of proteins, precipitation with alcohol and various purification methods). 

Although SPME was applied initially for the analysis of relatively volatile environmental pollutants in waters, rapid developments have enabled SPME to be successfully applied for the analysis of pesticides in water, wine and more complex food samples such as honey, fruit juice and pears, vegetables and strawberries. With food samples, most analysts recognize the need for some sample pretreatment in order to minimize matrix effects. The matrix can affect the SPME efficiency, resulting in a reduced recovery of pesticides. The most common method is simply to dilute the sample or sample extract with water. Simpltcio and Boas comminuted pears in water prior to the determination of pesticides. Volante et al. extracted over 100 pesticides... 

Once the comminution process is completed, the succeeding operations in mineral processing are taken over by what is known as separation. Regardless of the method or methods used, the aim is always the same-to take a natural aggregate of minerals (an ore) and separate it into two or more mineral products. In general, the products of separation are (i) the concentrate which contains the valuable minerals and (ii) the tailings which contain primarily materials of little or no value. It may be borne in mind that minerals have been liberated, either by grinding or by chemical means, must usually be sized prior to... 

Separation processes, as could be seen from Figure 2.1, position themselves at the back end of the sequence in operations in the mineral processing flowsheet. The front-end operations has been found virtually to terminate with the liberation or the size-reduction processes involving crushing and grinding. It is important to limit the amount of size reduction to that at which adequate liberation is accomplished. The term adequacy is related to the cost involved in comminution and to performance of the concentration methods that follows. The concentration is obtained by separation processes which rely on differences in the properties of the particles, the physical and physico-chemical characteristics of minerals. In this context, it will only be relevant to refer to Table 2.5 which presents a summary of the processes along with the properties of the minerals that are exploited. 

In the first group of methods, small particles are produced from larger ones by mechanical treatment. Naturally, it is an uneasy task to obtain homogeneous powders with uniform size distribution by means of comminution, therefore, in modem applications, chemical methods prevail. 

BARNES, K.A., SMITH, R.A., WILLIAMS, K., DAMANT, A.P., SHEPHERD, MJ.A., Microbore high performance liquid chromatography/electrospray ionization mass spectrometry method for the determination of the phytoestrogens genistein and daidzein in comminuted baby foods and soya flour, Rapid Comm. Mass Spectrom., 1998,12,130-138. 

---