Coatings prime coat

Topcoat with primer PVC coating Prime coating Polyester base fabric... 

Uses Emulsifier for cationic tack coats, prime coats... 

Cathodic Protection Systems. Metal anodes using either platinum [7440-06 ] metal or precious metal oxide coatings on titanium, niobium [7440-03-17, or tantalum [7440-25-7] substrates are extensively used for impressed current cathodic protection systems. A prime appHcation is the use of platinum-coated titanium anodes for protection of the hulls of marine vessels. The controUed feature of these systems has created an attractive alternative... 

A cmcial development for zinc phosphate coatings came in 1943 when it was found that more uniform and finer crystals would develop if the surface was first treated with a titanium-containing solution of disodium phosphate (6). This method of crystal modification is a prime reason for the excellent paint (qv) adhesion seen on painted metal articles. 

Rubber. A thin coating of mica acts as a mold-release compound in the priming of mbber goods such as tires. It prevents the migration of sulfur from the tire to the air bag when the tire is being vulcani2ed (see Tire cords). Mica is also dusted on mbber inner tubes to prevent sticking. 

The exceUent adhesion to primed films of polyester combined with good dielectric properties and good surface properties makes the vinyhdene chloride copolymers very suitable as binders for iron oxide pigmented coatings for magnetic tapes (168—170). They perform very weU in audio, video, and computer tapes. 

Poly(vinyl acetate) emulsions are used to prime-coat fabrics to improve the adhesion of subsequent coatings or to make them adhere better to plastic film. Plasticized emulsions are appHed, generally by roUer-coating, to the backs of finished mgs and carpets to bind the tufts in place and to impart stiffness and hand. For upholstery fabrics woven from colored yams, PVAc emulsions may be used to bind the tufts of pile fabrics or to prevent sHppage of synthetic yams. 

Rotary atomisation produces the most uniform atomisation of any of the aforementioned techniques, and produces the smallest maximum particle sise. It is almost always used with electrostatics and at lower rotational speeds the electrostatics assist the atomisation. At higher rotational speeds the atomisation is principally mechanical in nature and does not depend on the electrical properties of the coating material. If the viscosity of a coating material is sufficiendy low that it can be deUvered to a rotary atomiser, the material can generally be atomised. The prime mover is usually an ak-driven turbine and, provided that the turbine has the requked power to accelerate the material to the angular velocity, Hquid-dow rates of up to 1000 cm /min can be atomised using an 8-cm diameter beU. 

A frequently cited example of protection from atmospheric corrosion is the Eiffel Tower. The narrow and, for that age, thin sections required a good priming of red lead for protection against corrosion. The top coat was linseed oil with white lead, and later coatings of ochre, iron oxide, and micaceous iron oxide were added. Since its constmction the coating has been renewed several times [29]. Modern atmospheric corrosion protection uses quick-drying nitrocellulose, synthetic resins, and reaction resins (two-component mixes). The chemist Leo Baekeland discovered the synthetic material named after him, Bakelite, in 1907. Three years later the first synthetic resin (phenol formaldehyde) proved itself in a protective paint. A new materials era had dawned. 

Enamel coatings usually consist of several layers in which the prime coating is applied for adhesion but does not have the chemical stability of the outer layers. With cathodic polarization at holidays, attack on the exposed prime coating is possible as the cathodically produced alkali causes the defects to increase in size. This particularly cannot be excluded in salt-rich media. 

Because of their ease of use and their cost-effectiveness relative to other methods of assembly, pressure sensitive adhesives continue to penetrate all kinds of industrial applications. Some of the main reasons PSAs and PSA coated articles are prime candidates for industrial applications include the following ... 

Application of protective paints consists of surface preparation of steel, priming coat and finishing coats. Wherever possible, steel should be blast-cleaned before painting. Primers thoroughly wet the metal to promote adhesion of finishing paints and carry inhibitive pigments. For example, red lead oxide will minimize the spread of rust on metal surfaces. The total thickness of fmishing coats must be at least 0.125 mm for adequate protection and life. Four coats of paint usually are necessary to achieve this. 

All painting preparation, priming, finishing and protective coatings shall be in accordance with Specification Number ME-0-JGOO2. 

Another major type of coating process is wire covering. The tremendous demand for insulated cables in the electrical industry means that large tonnages of plastic are used in this application. Basically a bare wire, which may be heated or have its surface primed, is drawn through a special die attached... 

Anstrich, m. paint, painting, coat varnish dye tint, color appearance, -blndemittel, n. (Painting) binder, -farbe,/, painting color, pigment priming,... 

---