Applications chlorine

Water chlorination is carried out by using both free and combined residuals. The latter involves chlorine application to produce chloramine with natural or added ammonia. Anhydrous ammonia is used if insufficient natural ammonia is present in the wastewater. Although the combined residual is less effective than free chlorine as a disinfectant, its most common application is as a post-treatment following free residual chlorination to provide initial disinfection. 

Disinfection by-products (e.g., adsorbable organic halides such as trihalomethanes) are more than 50% decreased compared to equivalent chlorine treatments in standardized AOX test with STABREX3. In practice, disinfection by-products are decreased even further in STABREX applications because less oxidant is required to control the microbial fouling process compared to bromine or chlorine applications. 

The dosage required for a chlorination application varies according to the specific purpose and the composition of the water to be treated. For example, the maximum recommended dosage (in mg/L, or ppm) for the reduction of BOD is 2, whereas that for the disinfection of a primary effluent is 20, and for the oxidation of the supernatant obtained in a water-treatment digester (see Section 11.1) can be as high as 140. 

Chlorine, CI2, a greenish-yellow gas (mp -101 °C, bp -34.1 °C) delivered in steel containers under a pressure of 6 atm at 21 °C, is extremely corrosive and toxic. The use of good hoods is imperative for any work involving chlorine. Applications of chlorine gas for oxidation purposes are rare rather, its compounds such as sodium, potassium, and calcium hy-... 

Several appropriate emergency container leak repair kits should be stored near the chlorine application facility. 

The formation of CBPs is influenced by pH, temperature, ammonia, carbonate alkalinity, chlorine dose, contact time, removal of natural organic matter before chlorine application, etc. Moreover, the composition of these mixtures may change seasonally resulting... 

Discuss the advantages and disadvantages of chlorine application for treatment of raw water in the Asian region. 

At millimolar levels of molecular chlorine, the reaction goes to 99% completion in a matter of a few seconds. Above pH 4.4, essentially no molecular chlorine remains in aqueous solution. Hypochlorous acid is a weak acid (pKa approximately 7.5) and thus, near neutrality, both the protonated form and the anion occur at appreciable levels. HCl-free solutions may be prepared by adding salts such as sodium hypochlorite (NaOCl, commercially available as a stabilized 5.25% [0.7 M] solution as a fabric bleach). Either chlorine gas or hypochlorite solutions can be used in large-scale water chlorination applications. In addition to water treatment, chlorine is also used as a disinfectant for beef, pork, and poultry carcasses and also as a bleaching agent for paper pulp and cake flour (Wei et al., 1985). The disinfecting ability of aqueous chlorine is closely associated with its vigorous oxidant character the redox potential for the reactions... 

In the chlorine application, oversize thread specifications apply only to the external valve thread. There are no oversize internal chlorine... 

Table 6.19.3 Important chlorine applications for intermediates and end products (Schmittinger, 2000).

Another method for the hydrogenoiysis of aryl bromides and iodides is to use MeONa[696], The removal of chlorine and bromine from benzene rings is possible with MeOH under basic conditions by use of dippp as a ligand[697]. The reduction is explained by the formation of the phenylpalladium methoxide 812, which undergoes elimination of /i-hydrogen to form benzene, and MeOH is oxidized to formaldehyde. Based on this mechanistic consideration, reaction of alcohols with aryl halides has another application. For example, cyclohex-anol (813) is oxidized smoothly to cyclohexanone with bromobenzene under basic conditions[698]. 

One of the most important applications of redox titrimetry is in evaluating the chlorination of public water supplies. In Method 9.3 an approach for determining the total chlorine residual was described in which the oxidizing power of chlorine is used to oxidize R to 13 . The amount of 13 formed is determined by a back titration with 8203 . 

Examples of the application of HPLC to the analysis of (a) acetaminophen, salicylic acid, and caffeine (b) chlorinated pesticides (c) tricyclic antidepressants and (d) peptides. (Chromatograms courtesy of Alltech Associates, Inc. Deerfield, IL). 

Anode Applications. Graphite has been used as the primary material for electrolysis of brine (aqueous) and fused-salt electrolytes, both as anode and cathode. Technological advances, however, have resulted in a dimensionally stable anode (DSA) consisting of precious metal oxides deposited on a titanium substrate that has replaced graphite as the primary anode (38—41) (see Alkali and chlorine products). 

B. Slootmaekers, S. Tachiyashiki, D. Wood, and G. Gordon, "The Removal of Chlorite Ion and Chlorate Ion from Drinking Water," in Chlorine Dioxide Scientific, Tegulatory and Application Issues, American Water Works Association, International Sjmposium, Denver, Colo., Nov. 1—2,1989. 

Flame-Retardant Applications. The flame resistance of polyolefins, unsaturated polyester, mbber, and many other synthetic materials can be improved by the iaclusion of chloriaated paraffias. The soHd 70% chlorine product is the preferred choice ia most polymeric systems, but the Hquid grades are widely used ia mbbers, polyurethane, and textile treatments. 

Because of the nature of some applications in which chlorinated paraffins are used, skin contact is inevitable and therefore an important potential route into the body. Skin absorption studies (7) have shown that chlorinated paraffins are very poorly absorbed through the skin and should not cause significant systemic concentrations. 

---