Chlorinated polyethylen

Heat stabilizers protect polymers from the chemical degrading effects of heat or uv irradiation. These additives include a wide variety of chemical substances, ranging from purely organic chemicals to metallic soaps to complex organometaUic compounds. By far the most common polymer requiring the use of heat stabilizers is poly(vinyl chloride) (PVC). However, copolymers of PVC, chlorinated poly(vinyl chloride) (CPVC), poly(vinyhdene chloride) (PVDC), and chlorinated polyethylene (CPE), also benefit from this technology. Without the use of heat stabilizers, PVC could not be the widely used polymer that it is, with worldwide production of nearly 16 million metric tons in 1991 alone (see Vinyl polymers). 

Fig. 10. Preparation and morphology of toughened PVC (a) secondary PVC grain (50—250 flm) (b) modified PVC with coherent primary grain (ca 1 -lm) (220). CPE = chlorinated polyethylene EVA = ethylene—vinyl acetate copolymers ABS = acrylonitrile—butadiene—styrene MBS = methyl...

Thermoplastics. There are five elastomeric membranes that are thermoplastic. Two materials, chlorinated polyethylene (CPE) and polyisobutylene (PIB), are relatively obscure. Thermoplastic materials can be either heat-fused or solvent-welded. In contrast to Hypalon and uncured EPDM, this abiHty to fuse the membranes together remains throughout the life of the material. However, cleaning of the membrane surface after exposure to weather is required. Correct cleaning procedures for specific membranes are available from the individual manufacturer. 

Other Accelerators. Amine isophthalate and thiazolidine thione, which are used as alternatives to thioureas for cross-linking polychloroprene (Neoprene) and other chlorine-containing polymers, are also used as accelerators. A few free amines are used as accelerators of sulfur vulcanization these have high molecular weight to minimize volatility and workplace exposure. Several amines and amine salts are used to speed up the dimercapto thiadiazole cure of chlorinated polyethylene and polyacrylates. Phosphonium salts are used as accelerators for the bisphenol cure of fluorocarbon mbbers. 

Dimercapto-l,3,4-thiadiazole derivatives, accelerated by amines, are used to cross-link chlorinated polyethylene. Polyisobutylene containing brominated i ra-methylstyrene cure functionahty can be cross-linked in polymer blends with dimercapto-1,3,4-thiadiazole derivatives accelerated with thiuram disulfides. Trithiocyanuric acid is suggested for use in polyacrylates containing a chlorine cure site and in epichlorohydrin mbbers. 

Natural mbber comes generally from southeast Asia. Synthetic mbbers are produced from monomers obtained from the cracking and refining of petroleum (qv). The most common monomers are styrene, butadiene, isobutylene, isoprene, ethylene, propylene, and acrylonitrile. There are numerous others for specialty elastomers which include acryUcs, chlorosulfonated polyethylene, chlorinated polyethylene, epichlorohydrin, ethylene—acryUc, ethylene octene mbber, ethylene—propylene mbber, fluoroelastomers, polynorbomene, polysulftdes, siUcone, thermoplastic elastomers, urethanes, and ethylene—vinyl acetate. 

Chlorinated Polyethylene. Chlorinating polyethylene under pressure results in a polymer having a chlorine content varying from 25 to 42%. The polymer requires the incorporation of carbon black and minerals for achieving good physical properties. The polymers handle like conventional polymers and can be mixed and processed on conventional mbber equipment. 

Chlorinated polyethylene (CPE) has excellent o2one, oil, and heat resistance. In addition chlorinated polyethylene has replaced chloroprene elastomers. CPE has a lower specific gravity than chloroprene compounds and produces compounds that are similar to CR in properties but with lower costs. In addition, due to high levels of chlorine in the polymer, the flame resistance of the compounds of CPE are high. 

Siding. The resin most used for siding is poly(vinyl chloride) homopolymer, compounded with modifiers, stabilizers, and pigments. Modifiers are most often acryhc esters, followed by chlorinated polyethylene or ethylene—vinyl acetate, used at 6—8 phr (parts per hundred resin). The modifier increases the impact strength of the rigid PVC. 

Maxillofacial polymers include the chlorinated polyethylenes, polyethemrethanes, polysiloxanes (see Elastomers), and conventional acrylic polymers. These are all deficient in a number of critical performance and processing characteristics. It is generally agreed that there is a need for improved maxillofacial polymers that can be conveniently fabricated into a variety of prostheses (218,227,228). 

Thermoplastic chlorinated polyethylenes are seldom used on their own but primarily in blends with other polymers, particularly PVC. If chlorination is taken to a level at which the polymer is only semi-compatible with the PVC, a blend with high impact strength may be obtained. In these circumstances the material is classified as an impact modifier. 

There have been some attempts to develop chlorinated polyethylene elastomers. The rubbers possess such attractive properties as very good oil, heat, flame, ozone, and weathering resistance and are also available in a convenient powder form. In spite of being marketed at competitive prices, the chlorinated polyethylene rubbers (designated as CM rubbers by ASTM) took... 

At one time butadiene-acrylonitrile copolymers (nitrile rubbers) were the most important impact modifiers. Today they have been largely replaced by acrylonitrile-butadiene-styrene (ABS) graft terpolymers, methacrylate-buta-diene-styrene (MBS) terpolymers, chlorinated polyethylene, EVA-PVC graft polymers and some poly acrylates. 

In addition to acting as impact modifiers a number of polymeric additives may be considered as processing aids. These have similar chemical constitutions to the impact modifiers and include ABS, MBS, chlorinated polyethylene, acrylate-methacrylate copolymers and EVA-PVC grafts. Such materials are more compatible with the PVC and are primarily included to ensure more uniform flow and hence improve surface finish. They may also increase gelation rates. In the case of the compatible MBS polymers they have the special function already mentioned of balancing the refractive indices of the continuous and disperse phases of impact-modified compound. 

ACS polymers, developed primarily in Japan, are grafts of acrylonitrile and styrene onto elastomeric chlorinated polyethylene. Although the polymer has good weathering properties it is somewhat susceptible to thermal degradation during processing and to date these polymers have been of limited interest. 

If corona, plasma, or flame treatment is chosen as the surface treatment, it is important to bond quickly after the treatment. Waiting several hours will reduce the effectiveness of the treatment. In some cases, attempts to bond 24 h after the treatment can give the same poor bonding results as if the plastic had never been surface treated. If surface oxidation is not possible, priming the surface with a chlorinated polyethylene primer is a second choice [95]. 

Chlorinated Polyethylene Polyethylene-Ethylacrylote Polyethylene-Vinyl acetate Polyethylene-Methacryllc Acid Polyphenyleneoxlde Poly-4 mef ylpentene(1) Polyethylene... 

Processability Styrene-acrylonitrile, methacrylate-butadiene-styrene, chlorinated polyethylene, PVC-ethyl acrylate, ethylene-vinyl acetate, chlorinated polyoxymethylenes (acetals)... 

Chlorinated polyethylene CPEs provide a very wide range of properties from soft/ elastomeric to hard. They have inherent oxygen and ozone resistance, have improved resistance (compared to PEs) to chemical extraction, resist plasticizers, volatility, and weathering. Products do not fog at high temperatures as do PVCs and can be made flame retardant. 

---