Carboxylic acids strengths

Indolmycin, biosynthesis of, 864 Inductive effect. 37, 562 alcohol acidity and. 604 carboxylic acid strength and. 758 electronegativity and, 37 electrophilic aromatic substitution and, 562... 

Strictly speaking, there is no weakening of the carboxylic acid strength due to the presence of the amine function, as had been mentioned in older literature. The weakening phenomenon is simply due to the quasi-exclusive presence of the zwitte-rionic form in the solution. In other words, there exists no carboxylic acid function. They are totally ionized. 

Perfluorinated carboxylic acids are corrosive liquids or solids. The acids are completely ionized in water. The acids are of commercial significance because of their unusual acid strength, chemical stabiUty, high surface activity, and salt solubiUty characteristics. The perfluoroaLkyl acids with six carbons or less are hquids the higher analogues are soHds (Table 1). 

Equation 20 is the rate-controlling step. The reaction rate of the hydrophobes decreases in the order primary alcohols > phenols > carboxylic acids (84). With alkylphenols and carboxylates, buildup of polyadducts begins after the starting material has been completely converted to the monoadduct, reflecting the increased acid strengths of these hydrophobes over the alcohols. Polymerization continues until all ethylene oxide has reacted. Beyond formation of the monoadduct, reactivity is essentially independent of chain length. The effectiveness of ethoxylation catalysts increases with base strength. In practice, ratios of 0.005—0.05 1 mol of NaOH, KOH, or NaOCH to alcohol are frequendy used. 

In order to become useful dmg delivery devices, biodegradable polymers must be formable into desired shapes of appropriate size, have adequate dimensional stability and appropriate strength-loss characteristics, be completely biodegradable, and be sterilizahle (70). The polymers most often studied for biodegradable dmg delivery applications are carboxylic acid derivatives such as polyamides poly(a-hydroxy acids) such as poly(lactic acid) [26100-51-6] and poly(glycolic acid) [26124-68-5], cross-linked polyesters poly(orthoesters) poly anhydrides and poly(alkyl 2-cyanoacrylates). The relative stabiUty of hydrolytically labile linkages ia these polymers (70) is as follows ... 

Another example is the acidities of a series of carboxylic acids. It is known that the substitution effect on these compounds also depends on the environment. The behavior of the halo-substituted acetic acids is one of the prototype problems for the solvent effect on acidity The order in strength of the haloacetic acids in the gas phase is... 

Even the earliest reports discuss the use of components such as polymer syrups bearing carboxylic acid functionality as a minor component to improve adhesion [21]. Later, methacrylic acid was specifically added to adhesive compositions to increase the rate of cure [22]. Maleic acid (or dibasic acids capable of cyclic tautomerism) have also been reported to increase both cure rate and bond strength [23]. Maleic acid has also been reported to improve adhesion to polymeric substrates such as Nylon and epoxies [24]. Adducts of 2-hydroxyethyl methacrylate and various anhydrides (such as phthalic) have also been reported as acid-bearing monomers [25]. Organic acids have a specific role in the cure of some blocked organoboranes, as will be discussed later. 

Carboxylic acids vary considerably in strength. Among the strongest is trichloroacetic acid (Ka = 0.20) a 0.10 M solution of C13C—COOH is about 73% ionized. Trichloroacetic acid is an ingredient of over-the-counter preparations used to treat canker sores and remove warts. 

However, it may be that the acid catalysis mechanism is more complex than that described by Scheme 6-5. Broxton and McLeish (1983) investigated the (ii)-diazo ether of a benzene derivative with a carboxy group in the 2-position. They also observed acid catalysis by added carboxylic acids, but, interestingly enough, the reactivity decreased as the strength of the added acid increased. 

Bifunctional catalysis in nucleophilic aromatic substitution was first observed by Bitter and Zollinger34, who studied the reaction of cyanuric chloride with aniline in benzene. This reaction was not accelerated by phenols or y-pyridone but was catalyzed by triethylamine and pyridine and by bifunctional catalysts such as a-pyridone and carboxylic acids. The carboxylic acids did not function as purely electrophilic reagents, since there was no relationship between catalytic efficiency and acid strength, acetic acid being more effective than chloracetic acid, which in turn was a more efficient catalyst than trichloroacetic acid. For catalysis by the carboxylic acids Bitter and Zollinger proposed the transition state depicted by H. 

Sf.i f-Test 10.8B List the following carboxylic acids in order of increasing strength CHCl2COOH, CH.COOH, and CH2C)COOH. 

In general acid catalysis, the rate is increased not only by an increase in [SH ] but also by an increase in the concentration of other acids (e.g., in water by phenols or carboxylic acids). These other acids increase the rate even when [SH ] is held constant. In this type of catalysis the strongest acids catalyze best, so that, in the example given, an increase in the phenol concentration catalyzes the reaction much less than a similar increase in [H30 ]. This relationship between acid strength of the catalyst and its catalytic ability can be expressed by the Breasted catalysis equation ... 

---