Carbodiimides addition

Add EDC (Thermo Fisher) to the above solution to obtain at least a 10-fold molar excess of EDC to the protein. Alternatively, a 0.5-0.1 M EDC concentration in the reaction mixture usually works well. To make it easier to add the correct quantity of EDC, a higher concentration stock solution may be prepared if it is dissolved and used immediately. To prepare the peptide-protein conjugate, add the solution from step 3 to 10 mg of EDC in a test tube. Mix to dissolve. If this ratio of EDC to peptide or protein results in precipitation, scale back the amount of carbodiimide addition until a soluble conjugate is obtained. For some proteins, as little as 0.1 times this amount of EDC may have to be used to maintain solubility. 

Carbodiimide/additive method, carbodi-imide method. 

The selenoureas needed for condensation can usually be prepared by addition of hydrogen selenide to a solution of the corresponding cyanamides or carbodiimides. They can be less dangerously and quite... 

Gyanamides and Derivatives A/-Chloro-/-alkylcyanamides, RN(C1)CN, are oils that have medicinal and other appHcations (99). Primary and secondary alkyl-A/-chlorocyanamides add photochemically to olefins yielding 1 1 adducts. By contrast, A/-chloro-A/-/-butylcyanamide initially rearranges photochemically to A/-chloro-Af-/-butylcarbodiimide, (CH2)3CN=C=NC1, prior to addition to olefins giving carbodiimides (67,100). 

Schollenberger added 2% of a polycarbodiimide additive to the same poly(tetra-methylene adipate) urethane with the high level of acid (AN = 3.66). After 9 weeks of 70°C water immersion, the urethane was reported to retain 84% of its original strength. Carbodiimides react quickly with residual acid to form an acyl urea, removing the acid catalysis contributing to the hydrolysis. New carbodiimides have been developed to prevent hydrolysis of polyester thermoplastics. Carbodiimides are also reported to react with residual water, which may contribute to hydrolysis when the urethane is exposed to high temperatures in an extruder [90]. 

In a manner analogous to classic nitrile iinines, the additions of trifluoro-methylacetonitrile phenylimine occur regiospecifically with activated terminal alkenes but less selectively with alkynes [39], The nitnle imine reacts with both dimethyl fumarate and dimethyl maleate m moderate yields to give exclusively the trans product, presumably via epimenzation of the labile H at position 4 [40] (equation 42) The nitrile imine exhibits exo selectivities in its reactions with norbornene and norbornadiene, which are similar to those seen for the nitrile oxide [37], and even greater reactivity with enolates than that of the nitnle oxide [38, 41], Reactions of trifluoroacetomtrile phenyl imine with isocyanates, isothiocyanates, and carbodiimides are also reported [42]... 

Closely related mixed amido/imido/guanidinato tantalum complexes of the type Ta(NR R )[(R R2N)C(NR )2]( = NR ) (R R = Me, Et R = Cy, Pr R = Pr", BuO were synthesized by the insertion of carbodiimides into to tantalum-amide bonds in imidotantalum triamide precursors, and the effects of ligand substitution on thermal properties were studied by TGA/DTA measurements. In addition, selected compounds were pyrolyzed at 600 °C and the decomposition products were studied by GC-MS and NMR spectroscopy. ... 

The treatment of isocyanates with 3-methyl-l-ethyl-3-phosphoIene-l-oxide (59) is a useful method for the synthesis of carbodiimides in good yields. The mechanism does not simply involve the addition of one molecule of isocyanate to another, since the kinetics are first order in isocyanate and first order in catalyst. The following mechanism has been proposed (the catalyst is here represented as... 

A useful method to synthesize ten and fourteen-membered ring imides 346 involved an initial condensation of macrocyclic -ketoestes 343 with alkyl or aryl isocyanates and carbodiimides, respectively, in the presence of a base [68]. After a nucleophilic attack of the enolate on the isocyanate C, the resultant amide N anion 344 induced a ring closure by addition to the keto group. Then, the intermediately formed four-membered ring 345 underwent a fragmentation... 

Out of three phases reported for Ca3N2 [12], to date only the cubic (a) nitride phase is confirmed, crystallizing in the anti-bixbyite type structure. In addition, the carbodiimide nitride Ca4(CN2)N2 [13] may hold for another unconfirmed calcium nitride phase, and Can(CN2)2N6 stands for the ill-defined CauNg [14]. Here we note again that carbon impurities may produce significant difficulties in reactions. 

Note that carbon monoxide inserts into the Zr-H bond of 1 (2 equiv.) to afford an T -formaldehydo-type complex [(Cp2ZrCl)]2(g-CH20) [200-202]. Iminoacyl zir-conocene complexes are formed after addition of 1 to isonitriles [203]. Carbon dioxide [183, 202] is reduced to formaldehyde with 1 (2 equiv.). C02-like molecules such as isocyanates RNCO [204], isothiocyanates RNCS [205], and carbodiimides RNCNR [204] are readily converted to the corresponding bidentate form-amido ligands. 

The activation of DMSO toward the addition step can be accomplished by other electrophiles. All of these reagents are believed to form a sulfoxonium species by electrophilic attack at the sulfoxide oxygen. The addition of the alcohol and the departure of the sulfoxide oxygen as part of a leaving group generates an intermediate comparable to C in the carbodiimide mechanism. 

The first version of SPPS to be developed used the t-Boc group as the amino-protecting group. f-Boc can be cleaved with relatively mild acidic treatment and TFA is usually used. The original coupling reagents utilized for SPPS were carbodiimides. In addition to dicyclohexylcarbodiimide (DCCI), N, (V -diisopropylcarbodiimide (DIPCDI) is often used. The mechanism of peptide coupling by carbodiimides was... 

In conclusion, IR analysis of polymer/additive extracts before chromatographic separation takes advantage mainly of straightforward transmission measurements. Without separation it is often possible to make class assignments (e.g. in the reported examples on plasticisers and carbodiimide hydrolysis stabilisers) it may eventually be necessary to use multivariate techniques. Infrared detection of chromatographic effluents is dealt with in Chapter 7. 

---