Calculations checking

Repetition of the calculations with N = 7.0 gives R = 2.519, R = 0.9782, and a calculated check value of N = 6.85, which is close enough. The final-product compositions and the (X values used are as follows ... 

Two types of office space are usually needed. One is the area where laboratory workers perform calculations, check proce-... 

If your calculator has the % key, then it handles percents directly. Check your calculator carefully. Often the percent function (%) is a second function. Often, you must enter the percent as the last term in the calculator. Check with the user guide of your calculator for specific information. Example ... 

Note R in joules should be used in all parts of the calculation. Check units carefully. 

Exchange the results of your calculations, check them, and use them to make the following calculations, assuming that a potential difference of 0.05 V is placed across the ends of the wire. 

Verification of design through data and calculation checks and validation of design through prototype tests, where applicable... 

JACSAT is the CODEN, a six-character, unique title abbreviation used to represent titles in manual or machine-based information systems. The CODEN source is the International CODEN Directory, administered by Chemical Abstracts Service. The sixth character of each CODEN is a computer-calculated check character that ensures the reliability of the CODEN in computer-based systems. 

A. 11 Perform the following calculations on an electronic calculator. Check the results mentally ... 

Record the final energies (eV) obtained for each geometry in the triplet and singlet states obtained from your single-point UHF calculations. Check (V) the preferred spin state of each geometry. 

While you are completing the calculation, check to make sure that all units are canceling. If they do not cancel, it is a warning that you have probably made an error in the setup or the solution of the problem. 

VELOCITY DISTRIBUTION FOR TURBULENT FLOW. Because of the dependence of important flow parameters on velocity distribution, considerable study, both theoretical and experimental, has been devoted for determining the velocity distribution in turbulent flow. Although the problem has not been completely solved, useful relationships are available that may be used to calculate the important characteristics of turbulence and the results of theoretical calculations check with experimental data reasonably well. 

Samples should be tested in accordance with the test methods referred to, or detailed, in the relevant specifications. To the validity of the results obtained should be checked (and as necessary, any calculations checked) before the material is released or rejected. 

Compost generates no am-nionia. Undersupplemented. Check compost formula calculations. Check Nitrogen content of raw materials. 

Using a calculator or personal computer program, use the appropriate data from the second and third segments of Table 11.1 to calculate the slopes for all five peaks used for both the external standard and internal standard calibration calculation. Check your values against those reported for peaks 2 and 3 in Table 11.2. 

If a multiple-choice question involves a calculation, do the calculation, check your work, and only then compare your answer with the choices. If you find a match, you have probably found the correct answer. Keep in mind, though, that your instructor has anticipated the most common errors you might make in solving a given problem and has probably listed the incorrect answers resulting from those errors. Always doublecheck your reasoning and use dimensional analysis to arrive at the correct numeric answer and the correct units. 

The average number of propylene oxide units per side chain is 5. Molecular weight of a side chain is 5 x 58 = 290 or 290 gms/side chain. The total number of grams of propylene oxide used is 24360. The number of side chains then is 24360/290 = 84 side chains. The cellulose D.P. is 120, then 84/120 = 0.7. The D.S. is 0.7. (Calculation check 120 x 0.7 = 84 side chains each side chain has 5 propylene oxide units or 84 x 5 = 420 units each unit weighs 58 gms or 420 x 58 = 24360 gms which is the weight of propylene oxide used to prepare the hydroxypiopyl cellulose. 

Calculational Checks of Plutonium Cross Sections by Comparison with Critical-Assembly Results/ >. A. Meneley, J. R. White (AND... 

According to the first rule, it is direct separation that should be in the first column (A B,C) (B C) according to the second rule, there must be indirect separation (A,B C) (A B). Calculation check-up proves that summary vapor flow in the two columns is 60% larger at direct separation than at indirect separation in the first column. 

What is the pH of a mixture of equal volumes of 0.040 M each monosodium glutamate and lysine monohydrochloride Look at a diagrams to decide upon the major reactions to use in approximate numerical calculations. Check for contradictions. Show that reaction is under 1 %. 

The Project Details menu will open a Project Details form as shown in Figure 1.21. This form will allow entry of the general details of the project and calculations. This also includes the Calculation Done by and Calculation Checked by options along with dates. Once the details are entered, pressing the OK button will transfer the information to the main Vessel form. 

---