Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Model CAD

ProcGen generates a scaled 3D model of the test specimen geometry, in the form of a faceted boundary representation. This model is made available for use by other software tasks in the system. The STEP file format (the ISO standard for product data exchange) was chosen to provide future compatibility with CAD models produced externally. In particular part 204 (faceted b-rep) of this standard is used. [Pg.767]

Developed computer-aided drafting (CAD) models of alternative ways to construct the CH2-ISS... [Pg.218]

After completion of the detailed planning, the results (P I flow diagram, technical data sheets, etc.) are summarized and pictorialized. For this purpose a model of the plant is prepared (plastic or CAD model). On the basis of this model construction of the plant with all auxiliary units is begun (Table 5.1-3). [Pg.312]

In addition to the conventional manufacturing of physictil prototypes (e.g., CNC milling) the rapid prototype technologies (RPT) are gaining more and more importance. RPT makes it possible to produce a physical artifact directly from its CAD model without any tools. Thus, it is possible to build the prototype of a complex part within a few days rather than the several weeks it would take... [Pg.1288]

D CAD/modeler Free-form surfaces, parametric geometry, trim curves, surface/material properties, assembly information Tessellation (static dynamic), data reduction (LOD), siuface properties — > textures, materials, reflection mapping... [Pg.2519]

Drawing data CAD model data Parts lists Standard libraries Project data NC data Software... [Pg.2843]

Fig. 3.7 Dielectric elastomer ocean wave power generator based on a proof mass, system tested at sea (top) and CAD model of a final system that might be used for supplying power to navigation and scientific buoys (bottom)... Fig. 3.7 Dielectric elastomer ocean wave power generator based on a proof mass, system tested at sea (top) and CAD model of a final system that might be used for supplying power to navigation and scientific buoys (bottom)...
The typical approach for a 3D-Simulation of the extrusion process is, to create a 3D-CAD-Model of the extruder, to perform the grid generation... [Pg.412]

Adnan, M. F., Daud, M. F., Saud, M. S. (2013). Contextual knowledge in 3D CAD modeling. Proceedings 5th Research in Engineering Education Symposium 2013, Putrajaya, Malaysia, pp. 15-25, July 5-6, 2013. ISBN 978-967-0194-35-6. [Pg.54]

Numerical control (NC) program is generated from the computer-aided design (CAD) model of the part using computer-aided manufacturing... [Pg.249]

D CAD is the most primitive CAD modeling technique. It only creates geometry entities (Ml a 2D plane. The basic 2D geometry entities are points, lines, arcs, circles, and splines. 2D CAD can only present the part model in a plane view. It is possible to use three plane views to describe a part. Commonly, the three plane views used are the top, front, and side views. [Pg.253]

See other pages where Model CAD is mentioned: [Pg.69]    [Pg.83]    [Pg.83]    [Pg.83]    [Pg.83]    [Pg.458]    [Pg.602]    [Pg.603]    [Pg.608]    [Pg.274]    [Pg.148]    [Pg.69]    [Pg.83]    [Pg.83]    [Pg.83]    [Pg.83]    [Pg.236]    [Pg.29]    [Pg.6]    [Pg.415]    [Pg.507]    [Pg.323]    [Pg.421]    [Pg.587]    [Pg.1124]    [Pg.1290]    [Pg.1292]    [Pg.1293]    [Pg.2852]    [Pg.2856]    [Pg.38]    [Pg.38]    [Pg.39]    [Pg.120]    [Pg.144]    [Pg.168]    [Pg.340]    [Pg.24]    [Pg.22]    [Pg.253]   
See also in sourсe #XX -- [ Pg.30 , Pg.36 , Pg.38 ]



SEARCH



CAD

© 2024 chempedia.info